Posted by sflem849 on July 09, 2012 at 05:50:09 from (69.197.84.39):
In Reply to: painting question posted by CNKS on July 08, 2012 at 08:08:47:
CNKS said: (quoted from post at 08:08:47 07/08/12) I was surprised when I warped mine. This was the hood off a 460, it flattened the lengthwise crease in the center of the hood, the rest was ok. I hope the guy or you that does your WD9 disassembles more than Colby64 did his 560. He didn't even remove the distributer or the oil cansiter, or the seat, or the steering column, etc. Anyplace there is a part left on, the rear of the part and the cast, etc behind it does not get proper coverage. Hard to do with a diesel like yours unless you remove the injection pump and all the tubes, which you or him probably does not want to do. Colby's gas tractor has a lot of unpainted parts, regardless of how good it looks. I have nothing else to do, so mine get 100% stripped -- but I don't have a diesel.
Don't worry, mine is already further apart than that. Can you imagine if he would have blasted and painted it when he first started showing pictures!?!
You brought up something I never thought would make such a difference. Gas start diesel. Truthfully I should have restored something like my '43 H before I took on a gas start.
I just bought a large TP pressure blaster. I think I will blast my own stuff now. I am going to leave the sheetmetal to the pro. This guy restored a $250,000+ Corvette this winter. Right now he has some Pontiac that looks like a 442 and a Chevelle in the shop.
Here are a couple shots of everything I have off the tractor. That new dstates guy was asking about what I was taking off so I took some pictures.
Don't worry about that fuel filter. It is a junk one off a parts motor I bought back from a scrap yard. The mag crane wrecked it when he picked it up. I am keeping it around for the fittings.
This is the bulk of the parts. A few of those things are going to be done by hand like the air cleaner. Will I get the oil pan or air intake pipe clean enough if I blast them?
Just got the radiator back. I am thinking about spraying the fins rattle can black. I know it hurts their cooling, but I don't think it would look very good all green and not evenly colored.
This post was edited by sflem849 at 05:51:51 07/09/12.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Madison's County - by Anthony West. Philip Madison has been a good friend of mine for quite some time. He has patiently suffered my incessant chit chat on the subject of tractors for longer than I care to remember, and on many occasions he has put himself out, dropped what ever it was he was doing, to come and lend a hand cranking handles, or loading a find onto a trailer. Although he himself has never actually owned or restored a tractor, he was always enthusiastic and always around helping with other peoples projects.
... [Read Article]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.