Antique Tractor Paint and Bodywork |
Re: Valspar hardener questions
[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]
Posted by souNdguy on May 31, 2007 at 06:29:30 from (12.65.198.27):
In Reply to: Valspar hardener questions posted by SGF on May 27, 2007 at 04:32:57:
I paint pretty much exclusively with the TSC paints. For the most part I use the TSC primer. For any big jobs i use the quart and gallon can of primer.. for some small jobs I have use dthe bps spray can primer. In a few situations where i ran out of BPS spray can primer I have run across the street and used (gasp!) wallmart spray can primer for small hanging parts. So far.. I can't tell the difference on which parts were bps spraygunned primed, BPS spray canned primed, or walmart spraycanned primed. The BPS paint WIL benefit froma hardner. High humidity and or low temps are to be avoided. I've not had good luck under 60' or much over 90'.. though if painting hot.. you may change your spray mix a tad... I usually use naptha to thin my BPS paint.. but if i had to spray in super hot weather and had no other choice.. i might cut my thinner mix with a hair of mineral spirits so it wouldn't flash off so quick. I use a respirator with a good organic cartridge, and I paint inthe open air.. ideally with about a 3mph breeze or so.. just enough to keep the vapors moving. Some people can be very sensitive to the 'iso' compounds in the hardners. While there has been some discussion that the valspar hardner may have less of these compounds than other hardners... it is deffinately still present. Safest bet is what you've heard.. a forced fresh air breather... that lets you paint in a booth if you wanted to... If you are like many of us.. you can practice some due diligence and make a good outside spray job with minimal risks. If you use it.. and even think you might be becoming sensitive to the iso compounds.. dump that spray gun of mix and forget about using hardner unless you get or make the right breather equipment. By the way.. you can get some pretty superior results with using bps, hardner, and painting outside. Soundguy
Replies:
Home
| Forums
Today's Featured Article -
Oil Bath Air Filters - by Chris Pratt. Some of us grew up thinking that an air filter was a paper thing that allowed air to pass while trapping dirt particles of a particles of a certain size. What a surprise to open up your first old tractor's air filter case and find a can that appears to be filled with the scrap metal swept from around a machine shop metal lathe. To top that off, you have a cup with oil in it ("why would you want to lubricate your carburetor?"). On closer examination (and some reading in a AC D-14 service manual), I found out that this is a pretty ingenious method of cleaning the air in the tractor's intake tract.
... [Read Article]
Latest Ad:
Super WD9.
[More Ads]
Copyright © 1997-2024 Yesterday's Tractor Co. All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor HeadquartersWebsite Accessibility Policy |
|