Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo Auction Link (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage
Auction 

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Ford 9N, 2N & 8N Discussion Board

Re: 51 Ford 8N


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by Dell (WA) on June 21, 2013 at 02:22:15 from (174.31.181.232):

In Reply to: 51 Ford 8N posted by Timmy S on June 20, 2013 at 19:19:19:

Timmy.......in late 1950, Ford changed from the weird 4-nipple frontmount dizzy to the more conventional 5-nipple sidemount. You can count nipples, can't you???

The weird 4-nipple dizzy has a 1-terminal squarecan ignition coil with insulative tar that melts after about 1-hr of running time. It takes about 4-hrs of cool-down or overnite for the tar to re-solidify so you can run again fer about 1-hr. Unfortunately, there is NO eazy cure for this problem. Many desperate frontmount owners "hogg-outt" the squarecan coil and wire in the more reliable roundcan coil. Remember, the squarecan coil NEEDS the MANDATORY "infamous ballast resistor" (mounted on the dash underneath the ammeter) Many N-owners "by-pass" this resistor for hotter sparkies and eazier starting. But guess what, that also causes the insulative tar to melt and makes weaker sparkies. DON'T DO IT.

Remember ittza 2-bolt, 15-min job to remove the frontmount dizzy and change the points (0.015") on the kitchen table. Just un-snapple yer capple and walk. Installation is a reversal of the removal ...except... finger start the 2-bolts and then install the rotor. Now rotate the rotor until the OFFSET drive tang fits the OFFSET camshaft drive slot. Now tighten the 2-bolts and re-snapple yer capple and yer good to go. Simple, eh?

Remember to POLISH the INVISIBLE CORROSION from between the points (0.015") after installation. Me? I clamp a $1-bill between the points and pull. Iff'n yer really cheap, tear a strip from HEAVY brown paper grocery sack and use that. ........HTH, Dell, yer self-appointed sparkie-meister


Replies:




Add a Reply

:
:
:

:

:

:

:

:

:

Advanced Posting Options

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.



 
Advanced Posting Tools
  Upload Photo  Select Gallery Photo  Attach Serial # List 
Return to Post 

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - It Can't Be Done! - A Tractor Story - by Neil Campbell. I'll never forget the time back when I was a boy baling hay on our Farm in Big Rapid, Michigan. The most memorable event that took place was a trip up the steepest incline on the farm pulling an old New-Idea baler with a pony-motor for power and a haywagon. I had just talked my Dad into buying an old John Deere B with 6-speeds ahead and I was real proud of it, except it was a little smaller than the Case tractor that we normally ... [Read Article]

Latest Ad: Rebuilt Injection pump for J D 1010. Call or text for pictures or more imformation.free shipping.U.S. No core charge [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy