Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo Auction Link (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage
Auction 

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Ford 9N, 2N & 8N Discussion Board

Re: Amp vs Volt Meter


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by Hobo,NC on March 08, 2013 at 17:50:51 from (98.17.107.107):

In Reply to: Amp vs Volt Meter posted by DollarBill on March 08, 2013 at 06:21:14:

Quoting Removed, click Modern View to see

1) "Ammeter tells you whether you're charging...."

You can show amps but still have a low charge...

You are 0 for 1

2)"voltmeter tells you how much voltage your battery is putting out."

The battery is a place to store power a voltmeter will show you the state of charge of the battery and the charging system...

You are 0 for 2

3)"if your voltmeter reads low, obviously you're not charging."

You are 1 for 3

4) "An ammeter will be more useful with a 6 volt system due to the limited availability of the smaller scale volt meters. Most volt meters are ranged for 12 volt systems."

2 for 4

6) "Detroit moved away from ammeters due to the potential fire hazard they posed behind the dash. Volt meters are safer and carry less liability."

If you say so thats worth a haft point

You are 2 1/2 for 5

6) "My personal choice would be an ammeter because it tells you immediately when you're charging system is acting up"

That's not a completely true statement it depends on the state of charge of the battery and the demand of the electrical system...A voltmeter does the same thing but will tell you more about the state of charge of the battery and gen/alt output...

You are 2 1/2 for 6...

Theirs also a chance and it happens often were a voltmeter are a ammeter will show a low charging state... Sometimes a battery will not accept a charge the regulator is satisfied so you have a low voltage/amp output but suffer from a slow no crank condition from the battery and starter... This is reverse of what folks would think and the hardest condition to diagnosis...

I have also had battery's that would not fail a load test and never show signs of failer... The complaint was low volt/amp output with the gauge are the charging light on...

Its like a compression test the test leads you to your next move I could not imagine trying to diagnosis a charging/starting system using a amp meter only are using a amp meter as my fist weapon... Like a compression test a voltmeter leads me in the direction I need to go its valuable info I must have... Are I will chase my tail waist my time and the customers money and not make a wild guess like you normally see... To bad voltage questions were not on the guru test...



This information is provided for those that want to strengthen their diagnostic ability,,, YMMV...

Ammeters vs. Voltmeters



Ammeters and voltmeters are the opposite of each other not only in terms of construction, but of circuit placement.



Ammeters must have current passing through them in order to measure it, and so must be placed in series inside of a circuit. Polarity must be observed, and their positive and negative leads must be connected to the positive and negative sides of the circuit, respectively. Also, their internal resistance must not be large or it will block too much current, and this will affect the way the circuit functions and hence the reading.



Voltmeters should not have any current passing through them, and so are placed in parallel with the circuit they are to measure. Their leads are placed on each side of the component of interest, and as with ammeters, polarity must be observed. If their internal resistance is too small it will not block enough current, and this will affect the measurement.

Ammeters vs. Voltmeters



Ammeters and voltmeters are the opposite of each other not only in terms of construction, but of circuit placement.



Ammeters must have current passing through them in order to measure it, and so must be placed in series inside of a circuit. Polarity must be observed, and their positive and negative leads must be connected to the positive and negative sides of the circuit, respectively. Also, their internal resistance must not be large or it will block too much current, and this will affect the way the circuit functions and hence the reading.



Voltmeters should not have any current passing through them, and so are placed in parallel with the circuit they are to measure. Their leads are placed on each side of the component of interest, and as with ammeters, polarity must be observed. If their internal resistance is too small it will not block enough current, and this will affect the measurement.

Ampmeters must have current passing though them in order for them to measure it (not of much help on a no crank)

http://www.egauges.com/ATM_Tips.asp?TipPage=voltmeterammeter.htm


Replies:




Add a Reply

:
:
: :

:

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


 
Advanced Posting Tools
  Upload Photo  Select Gallery Photo  Attach Serial # List 
Return to Post 

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Talk of the Town: Modern Diesel Fuel in an Old Tractor - by Staff. This interestin discussion is from the Tractor Talk Discussion Forum. Remember that safety is your first priority - make sure you know what you are doing before attempting a potentially dangerous activity! ... [Read Article]

Latest Ad: Rebuilt Injection pump for J D 1010. Call or text for pictures or more imformation.free shipping.U.S. No core charge [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy