Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo Auction Link (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage
Auction 

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
Ford 9N, 2N & 8N Discussion Board

Re: oil change on an 8N Ford 1952


[ Expand ] [ View Follow Ups ] [ Post Followup ] [ Return to Forum ]

Posted by Leemo on September 27, 2004 at 11:31:31 from (198.209.225.227):

In Reply to: oil change on an 8N Ford 1952 posted by Bill Rolland on September 27, 2004 at 11:07:48:

Not a real tough job. If you don't have a large enough crescent wrench or open end wrench to get the pan plug off I've used a large pipe wrench and cheater bar. Wish I knew what the heck he used to tighten the darn thing. The reason a 5 gallon bucket was recommended was because when that big plug comes out so does all 6 quarts of oil. whoosh, drained !! A regular pan tends to be real messy. You should have a metal strainer screen in the center of the plug that fits over the oil pickup tube. Just clean it out with gas or carb cleaner or whatever so it's nice and clean. Remove the nut on top of the oil filter canister on the left side of the engine then remove the small plug in the bottom of the canister to drain as much out of the filter as you can. Remove the oil filter. Wipe and/or rinse out the oil filter canister to get as much old sludge out as you can. Replace the oil filter cartridge and rubber canister seals and tighten down the lid and plug on the oil filter canister. Clean out the drain plug and put the screen back in then put the plug back in the tractor. Fill 'er up with fresh oil and you're good to go.
Good Luck, Lee


Follow Ups:




Post a Followup

:
:

Subject:

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Hydraulic Basics - Part 2 - by Curtis Von Fange. In the last entry to this series we gave a brief overview of hydraulic system theory, its basic components and how it works. Now lets take a look at some general maintenance tips that will keep our system operating to its fullest potential. The two biggest enemies to a hydraulic system are dirt and water. Dirt can score the insides of cylinders, spool valves and pumps. Wate ... [Read Article]

Latest Ad: Super WD9. [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy