Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo Auction Link (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage
Auction 

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  
John Deere Tractors Discussion Board

Re: JD m relief valve settings, how to???


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by rusty wheel on November 14, 2012 at 08:54:09 from (75.180.23.218):

In Reply to: JD m relief valve settings, how to??? posted by Cody2012 on November 13, 2012 at 18:41:52:

I just dug out my service manual 2013 and read about the relief valve setting. This book covers the model 40. To adjust the relief valve setting, first, adjust relief valve pressure for remote system to 1040 to 1080 psi. Then add .060 shim to provide relief valve pressure to excess of 1080 psi while touch-o-matic relief valve is being checked. THE .060 SHIM MUST BE REMOVED AFTER TESTS ARE COMPLETED. DO NOT MOVE REMOTE CONTROL VALVE LEVER WHILE THESE SHIMS ARE IN THE VALVE AS DAMAGE MAY RESULT. Raise the draft links until the lift arms are parallel to floor and block them up.Move control lever forward and remove the 1/2 inch pipe plug from valve housing. Install a 3/8 inch pipe plug into the tapped passage directly below the plug just removed. Then install a hydraulic pressure gauge which will measure at least 2000 psi into the opening from which the 1/2 plug was removed. With the control lever in forward position, start tractor and let it reach it's normal operating temperature. Move enging speed control lever to wide open and while observing pressure gauge, slowly pull the tom control lever to the rear. Relief valve operatijng pressure should be 1040 to 1080 psi. A audible "whir" will be noted when relief valve opens. If the relief valve operating pressure needs to be reset, drain oil and remove rock shaft housing. Reset the pressure by turning the adjusting screw in to increase and out to decrease the pressure setting. Use special wrench to set and lock relief valve adjusting s and lock screw. NOTE one complete turn of the adjusting nut against the relief valve spring increases the pressure 120 lbs. When removing the pressure gauge after pressure has been set be sure all pressure has been relieved by stopping engine and moving control lever forward as far as possible. Remove the 3/8 pipe plug and reinstall the 1/2 pipe plug and tighten securly.


Replies:




Add a Reply

:
:
:

:

:

:

:

:

:

Advanced Posting Options

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.



 
Advanced Posting Tools
  Upload Photo  Select Gallery Photo  Attach Serial # List 
Return to Post 

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - It Can't Be Done! - A Tractor Story - by Neil Campbell. I'll never forget the time back when I was a boy baling hay on our Farm in Big Rapid, Michigan. The most memorable event that took place was a trip up the steepest incline on the farm pulling an old New-Idea baler with a pony-motor for power and a haywagon. I had just talked my Dad into buying an old John Deere B with 6-speeds ahead and I was real proud of it, except it was a little smaller than the Case tractor that we normally ... [Read Article]

Latest Ad: Rebuilt Injection pump for J D 1010. Call or text for pictures or more imformation.free shipping.U.S. No core charge [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy