Yesterday's Tractor Co. Tractor Parts for All Brands
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads

Community
Discussion Forums
Project Journals
Tractor Town
Your Stories
Show & Pull Guide
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

Related Sites
Tractor Shed
TractorLinks.com
Ford 8N/9N Club
Today's Tractors
Garden Tractors
Classic Trucks
Kountry Life

Enter your email address to receive our newsletter!

subscribe
unsubscribe
  
Implement Alley Discussion Board

Re: Planter clutch


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by JD Seller on December 24, 2012 at 19:31:22 from (208.126.196.144):

In Reply to: Planter clutch posted by mudcreek183 on December 24, 2012 at 12:43:29:

I would go check where you planted last and see if it was skipping. If the clutch skips the whole planter width would have a missed spot.

Like someone else stated: You may just need to clean the clutch up. Plus the teeth are not real sharp on a new clutch. The corners are not what drive it. The surfaces that lock together should be flat or straight. If they are that way I would just clean it all up.

To change this clutch you have to slide the drive shaft clear out of the wheel assemblies far enought to slide the clutch off. It is a real PIA to do. This is harder on the conservation models. You will need plenty of emery paper to polish everything up to get it apart and back together. If you have it apart than replace both halves and the spring.

That would be part# 15,16,23,and 29. They cost about $160 total. Plus a good half a day to get them installed.

So I would make sure it is skipping before I did that work. Also a loose chain will make it skip too. You need the one in the seed population transmission to be good and tight. I have seen guys just tighten them by hand and have a skipping problem. I always use a big pair of Channel locks to hold the tightener good and tight then tighten the lock screw.


Replies:




Add a Reply

Name:
E-Mail:
Subject:

Comments:

Optional Link URL:
Link Title:
Optional Image URL:
Optional Video Title:
Optional Video Embed:

Advanced Posting Options

Email Notification: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.



 
Advanced Posting Tools
  Upload Photo  Select Gallery Photo  Attach Serial # List 
Return to Post 
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ More Info ]

Home  |  Forums


Copyright © 1997-2014 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters