Welcome! Please use the navigational links to explore our website.
PartsASAP LogoCompany Logo Auction Link (800) 853-2651

Shop Now

   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts
Salvage
Auction 

Community
Discussion Forums
Project Journals
Your Stories
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

  

Re: Fordson Model F


[ Expand ] [ View Replies ] [ Add a Reply ] [ Return to Forum ]

Posted by Maine Fordson on August 21, 2010 at 06:11:11 from (74.75.196.56):

In Reply to: Fordson Model F posted by kenneth armour on August 20, 2010 at 13:37:24:

You can't see the commutator in your photos because of the angle at which they were taken. It's just a small part, about 3 inches in diameter, and about an inch thick. Go to https://www.thefordsonhouse.com/storefront.asp?subcat=189#189 to see a picture of this part.

I'm standing by my opinion of the purpose of those two studs at the front of the engine (i.e., being the remnants of a governor attach point). If you look at the manifold in the fifth photo of your last posting, in front of the #2 spark plug you'll see where the governor was attached to the manifold. Either it malfunctioned and was removed, or someone needed it worse than the current owner. (Which would explain the missing commutator linkage.) A governor is not essential, but it's a nice accessory if you are doing belt work; it saves the trouble of constantly adjusting the throttle. (This engine was designed to run at 1000 RPM, and no faster.)

The rest of the tractor looks great. Radiator looks good, the radiator sides are not cracked or broken, fenders are in great shape, and almost everything is there. The only other thing I see missing is the starting tank, which should be attached to the air washer (in the same pictured referenced above, look to the left of the manifold, behind the fuel line and below the air intake. The rectangular place with the two mounting ears is where the starting tank should be mounted. Most importantly, the manifold looks good, and seems complete. The manifold is a Holley 295, which is a later style, so that means the manifold was replaced sometime during the last 85 years. Also, the coil box looks to be the later style (but my memory fails me as to what year the change occurred). Replacement covers are available.

Have you looked up the serial number? It's stamped into the block just above the first manifold bolt, nearest the radiator. (You may need a small wire brush or a scraper to remove rust or grease.) A production matrix is available on this site. Serial Number List for FDS: Model F

Buy it!

-- Maine Fordson

This post was edited by Maine Fordson at 06:13:24 08/21/10.



Replies:




Add a Reply

:
:
Subject: :

:

:

:

:

:

: If you check this box, email will be sent to you whenever someone replies to this message. Your email address must be entered above to receive notification. This notification will be cancelled automatically after 2 weeks.


 
Advanced Posting Tools
  Upload Photo  Select Gallery Photo  Attach Serial # List 
Return to Post 

TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Today's Featured Article - Oil Bath Air Filters - by Chris Pratt. Some of us grew up thinking that an air filter was a paper thing that allowed air to pass while trapping dirt particles of a particles of a certain size. What a surprise to open up your first old tractor's air filter case and find a can that appears to be filled with the scrap metal swept from around a machine shop metal lathe. To top that off, you have a cup with oil in it ("why would you want to lubricate your carburetor?"). On closer examination (and some reading in a AC D-14 service manual), I found out that this is a pretty ingenious method of cleaning the air in the tractor's intake tract. ... [Read Article]

Latest Ad: Super WD9. [More Ads]

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy