While I like sending biz to this site, I suggest that this is one time to be careful, esp. since, as Soundguy says, this is a spendy changeover. The '65-Sep '68 (roughly) tractors use a different Zenith carb than the Sep '68-'75 tractors. This distinction is missed by 99% of parts sellers, including this site.
The early-late 3000s had this same quirk as the 3-cyl early-late 2000s. I'll give an example of the 3000s. The CNH (factory) web site isn't working well right now so I've dug out the following 3000 info as an example, so check things on the CNH site when it's up and get the 2000 info - before spending $s: Zenith: Early ('65-'68) - E1NN9510EA Late ('68-'75) - E1NN9510BA To further confuse you, you'll have to be careful on the CNH site because (IIRC), the Holley is listed as the same # except for the last two alpha digits.
Too many sellers and sites, if you look up the part for the early tractor, will link you to the later model carb.
The later model carb is NOT a universal fit. If you trace back thru the CNH parts pages, you'll find (as I did) that the early model governor and linkage is completely different than the later models. What this means, as far as I can tell, is that same Zenith carb body was used across all those years but the linkage (bell cranks, atch points, etc.) differs between early & late.
Besides the OEM factory site - CNH dot com - about the only other seller I ever found who recognized this distinction is farmersserviceinc dot com (note the double-S in the address).
Full disclosure: This subj has two camps of thought on this forum - check thru the archives if you haven't already. There are those who love Holleys and can get 'em to run well and they'll say rebuild 'em. There are others (me included) who went that oft-frustrating route and prefer to scrap the Holley. We bit the bullet 5-6 yrs ago and put the dinero into the Zenith for our '65 3000 and haven't had a lick of trouble since. For me, a tipping point in the decision was when I found that Holleys are NLA from CNH (and haven't been available for some time) - only new Zeniths are available from the OEM.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]
Today's Featured Article - Madison's County - by Anthony West. Philip Madison has been a good friend of mine for quite some time. He has patiently suffered my incessant chit chat on the subject of tractors for longer than I care to remember, and on many occasions he has put himself out, dropped what ever it was he was doing, to come and lend a hand cranking handles, or loading a find onto a trailer. Although he himself has never actually owned or restored a tractor, he was always enthusiastic and always around helping with other peoples projects.
... [Read Article]
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.