Yesterday's Tractor Co. Compare our Prices For Parts
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Tractor Manuals
Tractor Parts
Classified Ads
Photo Ads

Community
Discussion Forums
Project Journals
Tractor Town
Your Stories
Show & Pull Guide
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

Related Sites
Tractor Shed
TractorLinks.com
Ford 8N/9N Club
Today's Tractors
Garden Tractors
Classic Trucks
Kountry Life
Enter your email address to receive our newsletter!

subscribe
unsubscribe
  
Garden Tractors Discussion Forum

john deere snowthrower

Author  [Modern View]
breimer

12-09-2012 13:56:55
204.112.53.65



Report to Moderator

Blew snow yesterday wit a fairly worn out snowthrower (47inch Deere for a 400 tractor.) It worked very poorly. I noticed that the auger is worn badly making a lot of clearance at the center where the chute comes up. Probably need to replace the auger or weld it up. Does someone know how much clearance there is supposed to be? Currently it just blows the snow round the auger and not much comes out the chute unless I get a lot deeper or heavier snow.

[Reply]   [No Email]
steve_in_mo

12-09-2012 14:18:45
205.240.41.69



Report to Moderator
 Re: john deere snowthrower in reply to breimer, 12-09-2012 13:56:55  
A single-stage snowthrower needs to run with the engine at wide open throttle and full of snow to do much good. Reducing the clearance between the paddles and the sheet metal would help. You only need an eighth of an inch if things are round. If it's all beat up you need an eighth inch clearance at the tightest spot. Cleaning up the rust inside the thrower and painting and/or spraying with wax or cooking oil helps too.

[Reply]  [No Email]
[Options]  [Printer Friendly]  [Return to Forum]   [Add a Reply]

Hop to:
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ More Info ]

Home  |  Forums


Copyright © 1997-2014 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters