(800) 853-2651
SHOP NOW

Woods mower 59

H

Hebert

New User
I have 1970 International Cub with a Woods 59 belly mower under it, I am looking for a replacement deck to transfer the spindles and blades to. Does any one know where I can find one at in I live in Dunkirk Ohio. It is a 60 inch deck.thanks for any help
 
There is a salvage yard down in Hamilton Oh. that specializes is cubs and wood mowers. I have used there services and had good results. There email is [email protected]. Hope this helps. If unable to contact with this info get back to me and I'll see if I can find any other addresses. Larry
 
I googled them and came up with a little more info. Their website is www.hamiltonbobscubs.com and the phone no. is 513-582-8424
 
Hi Erik are you talking Ontario Canada, or Ohio, if it it Ohio would you mind sending pictures of the deck and how much you want for it, thanks.
 
Hebert,
I had a 5 ft woods mower off on a IH C. I was lucky to sell it complete, brackets, pulley and all for $300. Check Craigslist and even on YT for used woods mower decks.

Try using searchtempest.com. It will search all craigslists for a given number of miles from you. I use searchtempest all the time to find things.

However, my mower was a 1950. It looked more like a corn stock chopper than a finish mower. Grass discharged from both sides and the back. The spindles rotated to the right.

Not sure what a 1970 woods deck would look like.

George
 
Im in Ontario Canada but i will send you a picture any way. Thanks Erik..
a85002.jpg
 
I checked a couple sites that have online Woods parts books, and Woods doesn't list the deck as a replacement part...

There are plenty of them out there you just need to keep your eyes open.

Heck, go over and post in the WANTED section on farmallcub.com. Odds are someone will have an extra one they'd be willing to sell you at a fair price.
 
If everything goes right I found one for 100 dollars suppose to
pick up this weekend about 3 hours away
 
Picked my woods deck last night and starting the process of
fixing the few spots that needs welded and then repaint it
a85826.jpg
 
You must log in or register to reply here.

Similar threads

D
another fine mess
Replies
9
Views
484
Rich'sToys
R
D
How/when to sharpen blades? finish type mowers
Replies
6
Views
405
Cheesehead Fred
C
R
farmall cub implements
Replies
2
Views
238
Robert12345
R
D
Rear mount sickle mower for Super C w/ mid mount belly mower
Replies
6
Views
423
gene bender
G
T
Woods Mower
Replies
2
Views
551
Paul 300 U
P
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top