(800) 853-2651
SHOP NOW

Battery Cover Pictures for G1355

C

cleddy

Member
I don't know if this is what your tractor requires but this one is off a U302 Or M602 long battery. I was surprised no one seemed to have one and I felt fortunate to find this one in a scrap iron pile after a dozer was pushing it up in a tree pile. Maybe that where most of them ended up. Hope it helps. Cleddy
a132697.jpg

a132698.jpg

a132699.jpg

a132700.jpg

a132701.jpg

a132702.jpg

a132703.jpg

a132704.jpg

a132705.jpg

a132706.jpg

a132707.jpg

a132708.jpg

a132709.jpg

a132710.jpg

a132711.jpg

a132712.jpg
 
I don't know if that's right or not, I have two battery's, not the long skinny ones your talking about, but at least it kinda gives me an idea. Thanks for sharing.
 
I make reproduction ones of those. I believe they were also used on the early G1000 Vistas,but not after. I will have to check the parts books but I think the G900s, G950s might have shared the same cover but they used square type batteries on those. Will have to look into the 1355s.
 
Let me know if you make any covers for a 1355,I might be interested. the g1355 battery cover looks like it has a latch, and looks like it opens, not sure though. If you can see in this picture.
a132768.jpg
 
Diesel. Whats the difference of an lp one. Like to have one for when i repaint it sometime this winter.
 
If you can post a picture that be great. If i had the correct measurements and a picture i could make one.
 
Would the Oliver ones be similiar or did they do something different on those? Where was this picture taken?
 
I wonder if that was at the Humboldt SD show this last August. It looks like one I might have seen there.
 
The reason I asked the question LP or Diesel is I know the diesels use more batteries. So it might be a different configuration.
MMDEL
 
I was afraid of that. Looks like all you are going to get is the idea so maybe take that and make it fit your battery's. I've only seen about one tractor with cover's on so whatever you come up with will be fine. Put a little fancy stuff on and some radius corners and no one will know any different. I was hoping that the wrong one would bring out the right cover but no luck yet.Cleddy
 
You must log in or register to reply here.

Similar threads

P
116001
Replies
2
Views
109
Jim L WA
J
D
Template for grinding lift cover opening for new cylinde
Replies
3
Views
655
Ultradog MN
Ultradog MN
T
Ford 3000 governor linkage issues
Replies
0
Views
198
Travis152
T
J
What is this part for?
Replies
11
Views
1K
mdm1
mdm1
crsutton81
A few random pictures
Replies
17
Views
1K
Crazy Horse
Crazy Horse
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top