Kelly Lipinski
New User
I am looking for bracket specs to mount a 711 loader on a 1955 Ford 960. Any help would be much appreciated. My email is [email protected] if anyone has a drawing with measurements and could email me. Thank you.
- Thread starter Kelly Lipinski
- Start date
the hip bracket is the sticker, usually.. but perhaps not for a rowcrop.
the front hanger bracket and lower trans strap bracket are completely torchable.
normally the hanger bracket is near impossible to fab due to needing steering arm clearance on that side.
with you haveing a rowcrop, you could simply take some 1/2" plate ad a torch and sledge, and a piece of pin stock and heat/beat/ cut / weld up a side bracket that will work fine.
some pics of my 951 should give you an idea of the geometry,, close counts...
the front hanger bracket and lower trans strap bracket are completely torchable.
normally the hanger bracket is near impossible to fab due to needing steering arm clearance on that side.
with you haveing a rowcrop, you could simply take some 1/2" plate ad a torch and sledge, and a piece of pin stock and heat/beat/ cut / weld up a side bracket that will work fine.
some pics of my 951 should give you an idea of the geometry,, close counts...
Kelly Lipinski
New User
Thanks,
Is there any chance you could give me some hole and pin measurements.
Front Bracket - top frame bolt hole down to loader pin hole.
Hip bracket - pin down to bolt hole and offset
trans.bracket - bolt hole to bolt hole
Thanks
Is there any chance you could give me some hole and pin measurements.
Front Bracket - top frame bolt hole down to loader pin hole.
Hip bracket - pin down to bolt hole and offset
trans.bracket - bolt hole to bolt hole
Thanks
Kelly Lipinski
New User
Thankyou, whenvever you can send them will be fine. Thanks again.
Kelly Lipinski
New User
soundguy,
I sent you an email also, but just wanted to remind you about getting me those measurements.
Thanks,
Kelly
I sent you an email also, but just wanted to remind you about getting me those measurements.
Thanks,
Kelly
Kelly Lipinski
New User
I checked both my inbox and junk box and did not get the email? My email address is [email protected].
thanks
thanks
Kelly Lipinski
New User
I included my email with this post.
yep.. same address i sent ot at 8:55am est time
i pulled brackets off a tractor to measure.. then figured.. what the heck.. I'll template them on cardboard.
thus I have the cardboard templates to mail you.. should make duping the brackets much easier.
email me your snail mail address.
expect a large envelope from chris britton in florida in a few days after sending me your address.
i pulled brackets off a tractor to measure.. then figured.. what the heck.. I'll template them on cardboard.
thus I have the cardboard templates to mail you.. should make duping the brackets much easier.
email me your snail mail address.
expect a large envelope from chris britton in florida in a few days after sending me your address.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2024 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy