(800) 853-2651
SHOP NOW

Going rate for Crankshaft stroking?

N

NCWC

Member
Been a few years since iv had a crank welded and went with a local guy the last time. Just curious to know what prices are everywhere else.

Thanks
 
here in ohio, couple years ago 3/4 stroke on a 4 cylinder 1300. and that was after giving a break on the price.
 
Give this guy a call. 402-654-2217 he did a 9.25 for me for a lot better price than these guys are talking and he's good.

Jim
 
That's not a easy question to answer with the little info given. There's a big difference between a 2 inch stroke b John Deere and a 2 inch g John Deere. Time it takes to Weld and grind and balance is a whole lot more on the bigger, wider g crank. When it comes to cranks cheapest isn't usually the best.
 
Ok.. Looking to have a 4.5 inch 4 cylinder crank stroked to 5.75 inch. Or a 4 inch 6 cylinder stroked to 5.50 inch.
 
I had a 6" crank taken out to 7.25" for $900. The big Minnies run them as well as some good sized Farmall M pullers. I've not heard of one breaking. Hapco does dozens if not hundreds of cranks. Some of the big name engine builders are pretty happy with what they got.

Hapco Rebuilders
Terre Haute, IN
812-232-2550
 

The machine shop here is 250 to do the offset grinding and about $100 per crankpin to weld, but a little more for extreme welding work.

I have a couple allis cranks done a year and it's usually $750 to get them to 5.75 and 6" . I have a couple there right now and one of them is just to go on the shelf or sell.
 
I dont believe in pricing someone elses work . However I do believe that a crank thats done on a gleason m2 or m3 crank machine would be worth more than one thats not. The gleason m2 and m3 have two welding wires and ease of switching from the hard journal wire to the softer radius wire wich gives the crank better ability to flex and not crack as if it was done on a one wire machine where a guy doesnt take the time or expeditures to have and change wire back and forth.
 
You must log in or register to reply here.

Similar threads

B
1948 MM UTU 4.625x6.625 Crankshaft help needed!!
Replies
2
Views
320
T.R.K.
T
D
New to group & out for a test drive
Replies
1
Views
370
VicS
V
H
JD 950 with FEL, want to add PS
Replies
4
Views
331
Hntr984
H
R
Super C clutch pilot bearing
Replies
7
Views
333
Roger46
R
F
620 John Deere crankshaft tolerances
Replies
19
Views
691
Fidlstyks
F
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top