(800) 853-2651
SHOP NOW

1650 power beyond service manual

M

MikeO-WI

Member
looking for the service manual or picturs on how to hook up a power beyond on my 1650 for a loader. I looked in the archives but the pictures could not be found. Any help would be appreciated.
 
someone posted a copy some years back, there's a 1/2 pipe plug by the seat on the LH side of the hyd. unit facing forward, remove the plug then a few inches inside you need to screw in a 3/8 female hex or square pipe plug, then install piece 1/2 pipe nip ple with a 90degree elbow, plumb this ton the supply side of the valve, return oil goes into a 1/2 port on the lh side facing the wheel, hopefully someone else can explain it better
 
I don't know what you looked up on this site, but there have been many pictures on how to do this. However I don't think any were pictures of a 1650. The open center systems as used on the 00 & 50 series tractors will be the same. Get yourself a loader valve with float position as well.
 
I looked at a number of posts in archives last night but found where certain pictures were posted, they were deleted or removed. Might be something the archival process does. I even found a page by BA Star which references a service bulletin but the picture included is on a 3 pt mounted disk. I will try again later unless someone has something to post. Thanks
 
I filed away the service bulletin. It is dated 1966. Hope I can get it attached.
a96373.jpg
 
My 1600 is different from the 50 series tractors. There aren't any threads back in the hole where you take the plug out to get the output to the valve. You have to take the flow divider off and put a plug back in behind that. 1550,1650,1750 and 1850 should all have the threads in there and be the same as each other though.
 
The picture shows up, but the text is still blurry. Maybe try uploading it to the tractor picture site for better resolution?
 
You must log in or register to reply here.

Similar threads

C
oliver 1650 draft control plug won't come out.
Replies
1
Views
133
rrlund
R
EX Deere Farmer
Oliver 1650 high speed serial/model numbers
Replies
10
Views
562
super99
super99
D
Oliver 1650 hydraulic leak
Replies
4
Views
421
J. Schwiebert
J
T
Hydraulic noise when dead ended
Replies
13
Views
565
Mike(NEOhio)
M
G
Will Oliver 1650 gas motor fit anOliver1850 gas?
Replies
5
Views
600
ginacramer
G
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top