Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
Classified Ads
Photo Ads
Tractor Parts

Discussion Forums
Project Journals
Tractor Town
Your Stories
Show & Pull Guide
Events Calendar
Hauling Schedule

Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs

Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

Related Sites
Tractor Shed
Ford 8N/9N Club
Today's Tractors
Garden Tractors
Classic Trucks
Kountry Life
Using Your Tractor & Crop Talk

Discussion Board - drive gear

Welcome Guest, Log in or Register
Author  [Modern View]

08-16-2012 07:34:58

Report to Moderator

How bad is a chipped corner on a gear? is this a must fix? the tractor is not used heavily maybe 50 hours a year doing hay work

[Log in to Reply]   [No Email]

08-16-2012 10:16:42

Report to Moderator
 Re: drive gear in reply to danstone, 08-16-2012 07:34:58  
Hard to say with the lack of info. Depends in what gear it is and where it is and what tractor it is on. If in the engine that could mean a blown engine if in the transmission and a gear you do not use no big deal.

[Log in to Reply]  [No Email]

08-16-2012 07:55:11

Report to Moderator
 Re: drive gear in reply to danstone, 08-16-2012 07:34:58  
in my opinion ,if it has most of the gears contact point (90%) still there you likely be ok.Just make sure there are no hair line cracks accross other places in the gear. I drove a old grain truck for years that had about half a gear gone on the pinion. in fact i never knew it was broken until i had to put axle seal in.seen it was chipped then ,and drove it for another ten years or so. replacing it would be best of course but sometimes youve just got to get along with what you have .

[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:

Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

Home  |  Forums

Copyright © 1997-2016 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters