Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
Classified Ads
Photo Ads
Tractor Parts

Discussion Forums
Project Journals
Tractor Town
Your Stories
Show & Pull Guide
Events Calendar
Hauling Schedule

Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs

Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

Related Sites
Tractor Shed
Ford 8N/9N Club
Today's Tractors
Garden Tractors
Classic Trucks
Kountry Life
Tool Talk Discussion Forum

Re: Relaoding dies 30/30

[Show Entire Topic]  

Welcome Guest, Log in or Register
Author  [Modern View]

11-29-2012 12:44:17

Report to Moderator

Get a good reloading manual, follow it to the letter. Where they list the "DO NOT EXCEED" loads, they mean it. Wise if you stay a few grains of the recommended powder lower than that. My experience - middle of the road about halfway between "start" and "DON'T" produces the best accuracy. Have always worked loads up from the bottom of the powder recommednations - a grain or so at a time - load a few, shoot a few... Load a few somewhat heavier... 'Course, I have a chronograph available, and a range here on the farm for testing purposes.

By the way, the brand name is "Nosler", a very good manufacturer of excellent bullets. Other than what I cast myself, almost everything I load is Nosler. Except Hornady XTP in my muzzleloader.

[Log in to Reply]   [No Email]

11-29-2012 18:50:36

Report to Moderator
 Re: Relaoding dies 30/30 in reply to rabbit, 11-29-2012 12:44:17  
I have been reloading off and on now for decades and yes have more then one manual and I never load much if any over starting load. Read my other answers to get all my info on what we did and yes measured so as to know they came out at the 2.55 if I remember right as for how long they should be

[Log in to Reply]  [No Email]
[Show Entire Topic]     [Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:

Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

Home  |  Forums

Copyright © 1997-2016 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters