Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
Classified Ads
Photo Ads
Tractor Parts

Discussion Forums
Project Journals
Tractor Town
Your Stories
Show & Pull Guide
Events Calendar
Hauling Schedule

Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs

Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

Related Sites
Tractor Shed
Ford 8N/9N Club
Today's Tractors
Garden Tractors
Classic Trucks
Kountry Life
Discussion Forum

Re: 3/4 pvc

[Show Entire Topic]  

Welcome Guest, Log in or Register
Author  [Modern View]

10-24-2012 17:54:54

Report to Moderator

Lately I've been using these. Dig around the pipe, cut out the hole / break, slip this on, and tighten down. They work great!

[Log in to Reply]   [No Email]

10-25-2012 06:12:53

Report to Moderator
 Re: 3/4 pvc in reply to Puddles, 10-24-2012 17:54:54  
Those things look like a great idea, but I know of two that slowly slid apart. Both were in the open (not buried) - one in a basement, which resulted in water damage to lots of stuff, and the other in a pumphouse, which amazingly didn't seem to hurt the pump. The guy in the plumbing section at the local Lowes store sez "don't trust them - lots of them have failed". Maybe failed from improper installation, but how much more simple could they be. Both of the failures that I'm aware of were placed in lines that had a 90 degree bend. In a straight section, well supported, or buried, they "should" work good. . .

[Log in to Reply]  [No Email]
Old Bob

10-24-2012 18:05:07

Report to Moderator
 Re: 3/4 pvc in reply to Puddles, 10-24-2012 17:54:54  
I've used these before. They are the only way to do it.

[Log in to Reply]  [No Email]

10-24-2012 18:00:57

Report to Moderator
 Re: 3/4 pvc in reply to Puddles, 10-24-2012 17:54:54  
Those look like they would be a time saver. Thanks.

[Log in to Reply]  [No Email]
[Show Entire Topic]     [Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:

Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

Home  |  Forums

Copyright © 1997-2016 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters