Author	[Modern View]
Josh Russell 02-27-2013 17:03:07 184.6.199.117 Report to Moderator	I am looking for a rollamatic narrow front end for my John Deere 3010 and a guy gave me a rollamatic from under a John Deere 50 and said it would work . My 3010 has a wide front under it now so I have nothing to compare it with . If any one has any input for me on this I would greatly appreciate it . Thanks Josh [Reply]   [No Email]
tomstractorsandtoys1 03-03-2013 11:55:05 64.136.27.164 Report to Moderator	Re: Rollamatic in reply to Josh Russell, 02-27-2013 17:03:07   I maybe late to post on this but when you go to put your rollomatic on make sure you get the correct length bolts,they are 2 1/4 (I maybe wrong)if you use the wrong bolts it will mess the seal up in the bottom of the steering motor and you will not know it untill it starts leaking. [Reply]  [No Email]
Josh Russell 03-04-2013 16:03:24 184.6.199.117 Report to Moderator	Re: Rollamatic in reply to tomstractorsandtoys1, 03-03-2013 11:55:05   No you are not to late . I did not know that. Any information can always be useful. Thanks for the reply. [Reply]  [No Email]
JWuertz 03-02-2013 15:52:35 24.162.128.64 Report to Moderator	Re: Rollamatic in reply to Josh Russell, 02-27-2013 17:03:07   On my 54 jd60 it has the 4 bolt square pattern I,m not sure of the measurements though. what are they on your 3010? [Reply]  [No Email]
Josh Russell 03-02-2013 18:26:35 184.6.199.117 Report to Moderator	Re: Rollamatic in reply to JWuertz, 03-02-2013 15:52:35   My 3010 has an after market wide front end that is different than the actual john deeres . It is a really poorly made front end and it keeps breaking spindles were the tie rod connects to them . I am tired of fixing it and would like to take it back to original or at least a john deere front end . [Reply]  [No Email]
JWuertz 03-01-2013 03:41:03 24.162.128.64 Report to Moderator	Re: Rollamatic in reply to Josh Russell, 02-27-2013 17:03:07   would one from a jd 60 work? [Reply]  [No Email]
long green line man 03-02-2013 10:29:10 66.103.165.15 Report to Moderator	Re: Rollamatic in reply to JWuertz, 03-01-2013 03:41:03   One from 60 should be very similar , very early model 60 & late A with split pedestal are slightly dif. Late model 20 series (new gen) tractors used a improved ex.HD Roll-o-Matic. Id. by 3/8 bolts in plate att. spindle arm... [Reply]  [No Email]
Josh Russell 03-02-2013 14:09:55 184.6.199.117 Report to Moderator	Re: Rollamatic in reply to long green line man, 03-02-2013 10:29:10   Ok good to know . Thanks again for the information . Very helpfull. [Reply]  [No Email]
Josh Russell 03-01-2013 18:01:16 184.6.199.117 Report to Moderator	Re: Rollamatic in reply to JWuertz, 03-01-2013 03:41:03   I am not sure about that. It might. [Reply]  [No Email]
long green line man 02-27-2013 18:40:03 66.103.165.172 Report to Moderator	Re: Rollamatic in reply to Josh Russell, 02-27-2013 17:03:07   Roll-O-Matic from a 50 is very lite duty , small spindles & bearings, 3 bolt plate on spindle arm attach.. I'd look for a HD. 4 bolt plate, same spindle & bearing as your wide front... [Reply]  [No Email]
Josh Russell 02-28-2013 13:19:25 184.6.199.117 Report to Moderator	Re: Rollamatic in reply to long green line man, 02-27-2013 18:40:03   Ok good to know thank you for your response . [Reply]  [No Email]
Plant Doc 03-06-2013 03:34:23 71.168.196.176 Report to Moderator	Re: Rollamatic in reply to Josh Russell, 02-28-2013 13:19:25   I have a rollamatic from my 3010 that I converted to a wide front. I am willing to part with it for the cost of the freight. I am in NJ if interested. [Reply]  [No Email]
Josh Russell 03-06-2013 14:56:20 184.6.199.117 Report to Moderator	Re: Rollamatic in reply to Plant Doc, 03-06-2013 03:34:23   Thank you very much for the offer but I have located a front end a few miles from me that I am going to get after it gets warmer. [Reply]  [No Email]