Rear wheel weights on Super-C

Bob0465 · Oct 6, 2014

Can someone tell me how much the rear wheel weights on a Farmall Super- C weigh? Thanks

ejr-IA · Oct 6, 2014

I their the big singles 150#

Rick Remmert · Oct 6, 2014

The ones that came with mine weighted 145#. I have a total of 4 of them that I use to pull with. The 150# would be good enough.

Bob0465 · Oct 7, 2014

Thanks, I think if I removed them I could pull in the 3000 lb class

CLIFF S · Oct 7, 2014

Bob if all you're going to do is tractor pull take off the hydraulics on the tractor and replace the back gas tank bracket with one from a Farmall a you'll save 150 pounds.

PretendFarmer · Oct 8, 2014

(quoted from post at 04:09:23 10/08/14) Bob if all you're going to do is tractor pull take off the hydraulics on the tractor and replace the back gas tank bracket with one from a Farmall a you'll save 150 pounds.

With hydraulics removed on my 1948 C, the tractor weights just over 2500# with no one sitting on it and no weights on.

Bob0465 · Oct 8, 2014

I am pulling in the Farm Stock class and didn't know if removing the hydraulics would be allowed. That is good information to know. Thanks

PretendFarmer · Oct 9, 2014

(quoted from post at 01:32:39 10/09/14) I am pulling in the Farm Stock class and didn't know if removing the hydraulics would be allowed. That is good information to know. Thanks

Just remember your super C will always weigh more. 1948 was the lightest C ever.
Recently got into a bit of a tangle with someone because my wife drove our C and kicked his butt. He had a super C. We had way more weights on than he did because he's too stupid to realize a 1948 C weighs lots less than a super C. Plus he didn't have hyds removed and had wheel weights.

He thought we were cheating.

8v92guy · Oct 9, 2014

hey pf calling fred stupid is uncalled for. He is one of the most resepctfull pullers I have ever pulled with. I was not there but he was not the only one who thought you were way heavy. just saying

CLIFF S · Oct 10, 2014

Hydraulic arm where a option but very few where made with out them!

Not much can be said if all the options where took off and you got copies from Case IH parts book to prove it!

CLIFF S · Oct 10, 2014

My 48 C with out hydraulic or pto weight
in at 2800 no driver So you must have
light after market rims and tool box
etc striprd off to get that much lighter
than mine !
Cliff S

PretendFarmer · Oct 10, 2014

(quoted from post at 21:49:51 10/09/14) hey pf calling fred stupid is uncalled for. He is one of the most resepctfull pullers I have ever pulled with. I was not there but he was not the only one who thought you were way heavy. just saying

There are plenty of pics out there of that tractor at scaled pulls. I knew there would be an uproar over it here. It scales at 2680 with my 130# wife on and no weights. So you do the math. If that's wrong then the scale is wrong. It's the last time I go to any unscaled pull with this club.

showcrop · Oct 10, 2014

(quoted from post at 17:32:39 10/08/14) I am pulling in the Farm Stock class and didn't know if removing the hydraulics would be allowed. That is good information to know. Thanks

I don't know the Farmalls all that well, but Fords could be purchased new without hydraulics. A friend has a 900 with the original factory Hydraulics delete/seat support. It is hard to believe that there would not have been a demand for Super Cs stripped bare.

PretendFarmer · Oct 10, 2014

(quoted from post at 21:49:51 10/09/14) hey pf calling fred stupid is uncalled for. He is one of the most resepctfull pullers I have ever pulled with. I was not there but he was not the only one who thought you were way heavy. just saying

And I didn't say who or where.

8v92guy · Oct 10, 2014

that's right you didn't sat who or where. There is more folk from our club that go on this site than you may think. I do not want to argue with you. but calling a member of our club "to stupid to know the difference'' was a little over the top. you should listen to him and ask for advice rather than fight. He probably has forgotten more about farmalls than me or you will ever know.

PretendFarmer · Oct 10, 2014

When someone comes up to me and starts yelling at me calling me a cheat, that isn't going to be met with a pleasant response.

Let's not forget here, clubs need members. Not the other way around.

Elvin Frank · Oct 12, 2014

Pretend farmer, your a drama queen,
lol.....99% of your posts are drama
causing IMHO you need to work on your
people skills. There is a book out its
title is "How To Win Friends and Influence
People" Happy pulling and be weary of
those 8n's with low gears and movable
weights..........

PretendFarmer · Oct 12, 2014

(quoted from post at 17:45:45 10/12/14) Pretend farmer, your a drama queen,
lol.....99% of your posts are drama
causing IMHO you need to work on your
people skills. There is a book out its
title is "How To Win Friends and Influence
People" Happy pulling and be weary of
those 8n's with low gears and movable
weights..........

I spend little time complaining about other peoples behavior because I know it's not gonna change. I'd suggest you do the same.

Elvin Frank · Oct 13, 2014

I'm not complaining, I was making an
observation. I suggest you read the
book... ......

PretendFarmer · Oct 13, 2014

I'm illiterate.

Rear wheel weights on Super-C

Member

Member

Member

Member

Member

Well-known Member

Member

Well-known Member

Member

Member

Member

Well-known Member

Well-known Member

Well-known Member

Member

Well-known Member

Member

Well-known Member

Member

Well-known Member

Similar threads