|
| |
| Tractor Pulling Discussion Forum |
Topic: Re: Case VAC pullers
[Show Entire Topic] [Return to Forum]
| Author |
[Modern View]
|
| Cliff S
02-14-2013 23:36:08
70.192.128.124
|
My VAC works good in those Classes! Cliff S
|
|
|
| dboll
02-15-2013 05:40:34
209.23.168.231
|
|
Re: Case VAC pullers in reply to Cliff S, 02-14-2013 23:36:08
|
|
| That would't be the one Mel put a 201 into is it? Whether it is or not a 201 is not legal in NATPA.
|
|
|
| Cliff S
02-15-2013 12:15:26
70.192.128.124
|
|
Re: Case VAC pullers in reply to dboll, 02-15-2013 05:40:34
|
|
|  Doug No the VA mEL put a 201 in is DON FISHERS that have pulled in the past and you can not compare to a VAC anymore other than sheet metal ! I was talking about my VAC that I built to pull local pulls and dose well in 3000 3500 but is a little out powered in 4000 noncut but can get a win now and then!
My VAC has a NATPA WIN in 3000 Div 2 and a second in 3250 div 3 at tallmadge Oh but that's a weak track com paired to the other NATPA Tracks I been to! Cliff S
|
|
|
| MMZAck
02-15-2013 11:09:50
170.2.52.28
|
|
Re: Case VAC pullers in reply to dboll, 02-15-2013 05:40:34
|
|
| | Is the 201 engine considered USAP legal? Zack
|
|
|
| VicS
02-15-2013 11:16:48
70.195.66.17
|
|
Re: Case VAC pullers in reply to MMZAck, 02-15-2013 11:09:50
|
|
| It should be! Their rules say, if it is the same no. of cylinders, mfg and will bolt in.
|
|
|
| Mopower
02-18-2013 06:55:32
64.208.152.151
|
|
Re: Case VAC pullers in reply to VicS, 02-15-2013 11:16:48
|
|
| Unfortunately, the don't allow different deck height, even if bolt in like my 403 MM (unless it is a John Deere, then apparently it's ok). They also can't use a longer engine (Olie 77/88, Case VAC/201, IH 560/Red Dismond) unless Division 5.
|
|
|
| Cliff S
02-15-2013 12:18:32
70.192.128.124
|
|
Re: Case VAC pullers in reply to VicS, 02-15-2013 11:16:48
|
|
| | Vic The 201 won't bolt in with out drilling and taping the block to make fit! Cliff S
|
|
|
| VicS
02-15-2013 19:26:08
70.195.67.234
|
|
Re: Case VAC pullers in reply to Cliff S, 02-15-2013 12:18:32
|
|
| Cliff I know a guy that put a combine motor in a 300. He said it bolted right in. A 300 is old enough isn't it?
|
|
|
| Cliff S
02-15-2013 22:37:11
70.192.131.41
|
|
Re: Case VAC pullers in reply to VicS, 02-15-2013 19:26:08
|
|
| | Vic In usap it may be old enough but NATPA says production start 1959 and older for div 1,2,2t and 1957 and older for div 3,4 The other problem with the 201 is its longer block and that changes the wheelbase and that's a no no. Cliff S
|
|
| [Show Entire Topic]
[Options]
[Printer Friendly]
[Return to Forum]
[Add a Reply]
| Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a Company you can trust and have generous return policies! Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ More Info ] |
Home
| Forums
Copyright © 1997-2013 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor Headquarters |
About this site - Yesterday's Tractors is your one-stop source for antique tractors. If you are interested in older tractors you've come to the right place! Join more than 275,000 other classic tractor enthusiasts from all over the globe. We have many resources for antique tractor enthusiasts available including photos, classified ads, more than 24 tractor discussion forums, a show guide, values, specs and much more. Bookmark this site and come back often. Thanks for stopping by! Feel free to use our feedback form to send us your comments, suggestions and ideas.
|
|
|
