Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads
Tractor Parts

Community
Discussion Forums
Project Journals
Tractor Town
Your Stories
Show & Pull Guide
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

Related Sites
Tractor Shed
TractorLinks.com
Ford 8N/9N Club
Today's Tractors
Garden Tractors
Classic Trucks
Kountry Life
  
Oliver, Cletrac, Co-op & Cockshutt Tractors Discussion Forum
Show Parts for Model:

1650 lift arms dropping at low rpm

Welcome Guest, Log in or Register
Author  [Modern View]
dnd

12-02-2017 06:07:58




Report to Moderator

Good morning to all, finally got corn and beans off in Wisconsin!
This topic was crossed earlier this summer by someone else on this site, but here I go again. My 1650 will drop itís three point arms when the engine rpms are below 1100, when you increase the throttle the arms raise back up. Also this spring I needed to keep the tractor revíd up to raise the soybean drill. I remember someone mentioning that there is an elbow in the hydraulics under the seat that might be the cause as it tends to crack.

Now I have the seat off last night and am looking for the elbow.. I am sure I will need to get the hydraulic oil out but then where should I look.
Thoughts! HELP or suggestions needed.

[Log in to Reply]   [No Email]
rrlund

12-05-2017 07:21:54




Report to Moderator
 Re: 1650 lift arms dropping at low rpm in reply to dnd, 12-02-2017 06:07:58  
I think the one you're talking about is on the side of the 3pt cylinder itself. You have to take the whole top off the rear end and turn it upside down to get to it. I wonder if the problem is the o-ring on the piston being worn flat? I've had to change them on my 1850 and 1550. The 1550 would bounce though. It would start down,then catch itself and raise back up quick over and over.



[Log in to Reply]  [No Email]
dnd

12-05-2017 17:47:23




Report to Moderator
 Re: 1650 lift arms dropping at low rpm in reply to rrlund, 12-05-2017 07:21:54  
Got everything apart tonight. Elbow looks good,,, what is the easiest way to get the piston out of the sleeve?



[Log in to Reply]  [No Email]
rrlund

12-06-2017 09:36:45




Report to Moderator
 Re: 1650 lift arms dropping at low rpm in reply to dnd, 12-05-2017 17:47:23  
You can stand it on end and just tap it on a wood block. I've used air before,but it seems no matter how little I try to blow in,it's too much and the piston comes flying out like it was shot out of a cannon.



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:


TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

Home  |  Forums


Copyright © 1997-2016 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters