|
| |
| Oliver, Cletrac, Co-op & Cockshutt Tractors Discussion Forum |
Topic: Re: Wristpin 60
[Show Entire Topic] [Return to Forum]
| Author |
[Modern View]
|
| Bob Frazier
02-24-2013 17:16:03
63.153.207.237
|
Thanks for your suggestion and help , am learning as i go on this tractor. Did a valve job on it and then heard this knock noise . Has plenty of oil pressure, so will probably check mains and rods while I'am in there. Bob F
|
|
[Reply] [No Email] | |
| M.Spitznogle
02-24-2013 19:28:13
67.55.184.65
|
|
Re: Wristpin 60 in reply to Bob Frazier, 02-24-2013 17:16:03
|
| Remember oil pressure is not affected by rod brg.clearance,Also you may want to catch all those shims when you take the rod cap off.
|
[Reply] [No Email] | |
| J. Schwiebert
02-24-2013 17:27:17
209.143.54.246
|
|
Re: Wristpin 60 in reply to Bob Frazier, 02-24-2013 17:16:03
|
| Well I did look and standard pin size on a 60 is .875 which is a common size. In fact when I did this machine work for a living we even had .003 & .005 oversize pins available. Without looking I think the little 8N Ford engines also used an .875 pin. Parts for those engine are plentiful. I should measure one of the extra rods we have laying around and make a note of the bore in the eye of the rod. J.
|
[Reply] [No Email] | |
[Show Entire Topic]
[Options]
[Printer Friendly]
[Return to Forum]
[Add a Reply]
| Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a Company you can trust and have generous return policies! Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ More Info ] |
Home
| Forums
Copyright © 1997-2013 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor Headquarters |
About this site - Yesterday's Tractors is your one-stop source for antique tractors. If you are interested in older tractors you've come to the right place! Join more than 275,000 other classic tractor enthusiasts from all over the globe. We have many resources for antique tractor enthusiasts available including photos, classified ads, more than 24 tractor discussion forums, a show guide, values, specs and much more. Bookmark this site and come back often. Thanks for stopping by! Feel free to use our feedback form to send us your comments, suggestions and ideas.
|
|
|
