Yesterday's Tractor Co. Compare our Prices For Parts
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads

Community
Discussion Forums
Project Journals
Tractor Town
Your Stories
Show & Pull Guide
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

Related Sites
Tractor Shed
TractorLinks.com
Ford 8N/9N Club
Today's Tractors
Garden Tractors
Classic Trucks
Kountry Life
Enter your email address to receive our newsletter!

subscribe
unsubscribe
  
Oliver, Cletrac, Co-op & Cockshutt Tractors Discussion Forum
Show Parts for Model:

Re: sleeve installation

[Show Entire Topic]  

Welcome Guest, Log in or Register
Author  [Modern View]
Rocko

01-16-2013 16:12:00
173.210.157.58



Report to Moderator

One of your O-rings may have rolled over on you and not be seated properly or possibley you might have something under the shoulder. Not sure if you would want to pull it again to check, you'll probabley need new O-rings for sure if you do. I think I would try to get it to sit to the same point as the others by using 2 or 4 bolts with big washers in your head bolt holes and cinch it down at the very least. Not easy to put preasure on water side with out head on but you might also first before any thing else want to at least put some water in to see if you have a leak when looking up from under side. That might give you an idea if your O-rings are okay. Is it normal, I don't have enough experience to tell you but when I rebuilt my 1550 I had pretty much the same situation,# 6 last cylinder at back if I remember correctly and I did what I have suggested to you. Still holding about 800 hrs later. Sure there are others out there with lot more know how than me and You'd probabley be wise to wait for their input. Just giving you my 2 cents. I had never rebuilt a motor before that and was worried and ancious about the end product. Hope this helps you. Rocko.

[Log in to Reply]   [No Email]
[Show Entire Topic]     [Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:

TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ More Info ]

Home  |  Forums


Copyright © 1997-2014 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters