Yesterday's Tractor Co. The Right Parts, Right Away
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Tractor Manuals
Tractor Parts
Classified Ads
Photo Ads

Community
Discussion Forums
Project Journals
Tractor Town
Your Stories
Show & Pull Guide
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

Related Sites
Tractor Shed
TractorLinks.com
Ford 8N/9N Club
Today's Tractors
Garden Tractors
Classic Trucks
Kountry Life
Enter your email address to receive our newsletter!

subscribe
unsubscribe
  
Oliver, Cletrac, Co-op & Cockshutt Tractors Discussion Forum
Show Parts for Model:

310 Gas crank grinding

Author  [Modern View]
IndianaOllie

10-20-2012 05:45:59
174.231.136.82



Report to Moderator

Im looking to get my 310 gas crank ground to 2in journals. The guy at the machine shop said it would cost about the same as to weld it. What are some of you guys paying for the 2in offset?




[Reply]   [No Email]
indiana ollie II

10-20-2012 06:07:22
72.53.194.237



Report to Moderator
 Re: 310 Gas crank grinding in reply to IndianaOllie, 10-20-2012 05:45:59  
950-1350



[Reply]  [No Email]
IndianaOllie

10-22-2012 13:01:17
12.44.210.21



Report to Moderator
 Re: 310 Gas crank grinding in reply to indiana ollie II, 10-20-2012 06:07:22  
Thanks. Might as well have a welded crank.



[Reply]  [No Email]
Indiana ollie II

10-22-2012 17:28:30
72.53.194.237



Report to Moderator
 Re: 310 Gas crank grinding in reply to IndianaOllie, 10-22-2012 13:01:17  
heard it can go to 5in with offset grinding. have your mains ground off and rebuilt to std. a good shop can double the hardened surface thickness to help strengthen the mains. 77 rods n a 2in comp height piston works good. good luck.



[Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Add a Reply]

Hop to:
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ More Info ]

Home  |  Forums


Copyright © 1997-2014 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters