(800) 853-2651
SHOP NOW

Screw holding straps on points

A

AteN

New User
Hi Again,

I've added a letter to the picture indicating the nylon screw that melted along with several things in my distributor: D indicates this screw.

Does this one have to be nylon? or can I put in a metal screw (if I'm lucky enough to find one that fits in well), these screws don't come with a set of new points.

Again, thanks in advance for your welcomed advice

Gord
 

Here is the new photo
a206484.jpg
 
The hold down screws were not nylon Gord, they were metal.
Just make sure it is not too long or it may interfere with the
advance weights under the point plate.
There are insulators at A and B and those need to be there.
 
Thanks Royse,

I see the confusion with the location of the letter D I added to the photo. It happened to be on the hold down screw word in the photo.

follow the little red arrow from the letter D to a screw on the straps (not the hold down screws). Thanks, I'll fix that and repost the picture

Gord
 
Sorry Gord, I looked at your picture wrong.
You are not pointing at the hold down screw.
That screw does not have to be nylon either,
but the insulators still need to be there.
 
Thanks Royse,

My fault, I put the letter in a dumb spot.

Trouble is trying to either make or find an insulator at C and finding a proper screw for D (although that will be easier now that it doesn't have to be nylon).

Thanks again for your help

Gord
 
I sure hope I'm following correctly here.
For "A" try Hillman part number 881189
Like the one linked [b:4b2a03a8ea]here.[/b:4b2a03a8ea]

This is a bit different part, but fixed the same way.

30393.jpg
 
Thanks Royse,

Looks darned close, I'll pick one up tomorrow and see how it goes. Even if I have to drill a small hole down the centre, it may just work.

Great, I have a mission :) thanks again for your help.

Gord
 
You must log in or register to reply here.

Similar threads

R
8N Trouble shooting
Replies
16
Views
1K
Ron Petterson
R
L
oil bath air filter MF 50
Replies
3
Views
687
Larcoats
L
M
New to me Franken-Fergie
2
Replies
37
Views
3K
Mad Farmer
M
A
Wico XH 1042 Magneto Magnet Rotor Rub
Replies
1
Views
417
jd man wis
J
D
Ford 641: no spark from rebuilt distributor
Replies
3
Views
586
JMOR
J
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top