(800) 853-2651
SHOP NOW

OK to drive 8n with lift cover off?

K

kylemorley

Member
Is there any good reason why I shouldn't drive my 8n when the lift
cover is off? Not far, just in and out of the garage a few times.
 
(quoted from post at 10:07:09 04/07/14) Is there any good reason why I shouldn't drive my 8n when the lift
cover is off? Not far, just in and out of the garage a few times.
Click to expand...

Lots of images jump to mind :roll: I can't think of any potential harm assuming you don't fall in but if it werre me I'd probably roll it :lol:

TOH
 
(quoted from post at 10:13:00 04/07/14)
(quoted from post at 10:07:09 04/07/14) Is there any good reason why I shouldn't drive my 8n when the lift
cover is off? Not far, just in and out of the garage a few times.
Click to expand...

Lots of images jump to mind :roll: I can't think of any potential harm assuming you don't fall in but if it werre me I'd probably roll it :lol:

TOH
Click to expand...
see a hyd oil enema IF PTO in gear. :lol: :lol:
 
(quoted from post at 10:30:14 04/07/14)
(quoted from post at 10:13:00 04/07/14)
(quoted from post at 10:07:09 04/07/14) Is there any good reason why I shouldn't drive my 8n when the lift
cover is off? Not far, just in and out of the garage a few times.
Click to expand...

Lots of images jump to mind :roll: I can't think of any potential harm assuming you don't fall in but if it werre me I'd probably roll it :lol:

TOH
Click to expand...
see a hyd oil enema IF PTO in gear. :lol: :lol:
Click to expand...

That was one of teh images that came to mind :roll:

TOH
 
Hate to disappoint everyone, but I bolted a scrap of plywood down over the hole, mainly to keep water and mice out, but also me.
 
You must log in or register to reply here.

Similar threads

D
Lift ram arm cracked lift cover.
Replies
8
Views
1K
Dave G9N
D
D
Template for grinding lift cover opening for new cylinde
Replies
3
Views
653
Ultradog MN
Ultradog MN
L
Lift Arm Control Help
2
Replies
26
Views
2K
JMOR
J
J
Hydraulic pump rebuild?
Replies
7
Views
420
JMOR
J
D
Aftermarket lift cylinder - more grind to fit.
2
Replies
22
Views
1K
Dave G9N
D
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top