(800) 853-2651
SHOP NOW

Ford 600 genny

T

TomN

Member
.... just took my ford 600 Genny for rebuild... bearing bad in front plate.... knew it was going... SoundGuy had told me that 6.5 volts was low.... Genny started making bad noise.... shut down immediatley...as to avoid further damage... will cost about $45.00 from local guy to do.... will put out 7.1 volts when finished :) Arm. is good... no damage from being "out of line"... due to not running machine after noise was heard....

... need new PTO shaft for this machine also... as spline is bent....
 
(quoted from post at 16:41:49 02/20/13) .... just took my ford 600 Genny for rebuild... bearing bad in front plate.... knew it was going... SoundGuy had told me that 6.5 volts was low.... Genny started making bad noise.... shut down immediatley...as to avoid further damage... will cost about $45.00 from local guy to do.... will put out 7.1 volts when finished :) Arm. is good... no damage from being "out of line"... due to not running machine after noise was heard....

... need new PTO shaft for this machine also... as spline is bent....
Click to expand...
onder where those extra 0.6 volts will come from? Certainly not from bearing!
 
JMOR... he is going to fully tet genny after done... 2 brush system appeared to be fine, but hey, I am not a generator expert... I am sure I will know more "beyond" my reasoning, once he looks at it... lol
 
... I know some of the 9n and 8n generators had a 'high/low" adjustment.... this one does not... is there any credence to an adjustment in voltage regulator on a ford 640?

just curious
 
(quoted from post at 17:03:50 02/20/13) ... I know some of the 9n and 8n generators had a 'high/low" adjustment.... this one does not... is there any credence to an adjustment in voltage regulator on a ford 640?

just curious
Click to expand...
es, VRs are adjustable. Joe Shadetree will not normally be successful in adjusting attempt, but a knowledgeable generator man can do. If he has both your VR & generator he will likely deliver as promised. :)
 
yup.

my guess is he had brush problems too.. as in no contact.

it's a wonder the fields aren't cut.. see that alot.
 
Genny is repaired and back on.... Tractor is back in service... damage was at a minimun, as I did not run it after realized issue... 2 days/45 bucks.... he had to solder something on the arm. replace front bearing... Brushes in great shape... now puts out 7+ volts... Volt reg fine... evrything is "nominal".... :)
 
(quoted from post at 16:30:38 02/22/13) Genny is repaired and back on.... Tractor is back in service... damage was at a minimun, as I did not run it after realized issue... 2 days/45 bucks.... he had to solder something on the arm. replace front bearing... Brushes in great shape... now puts out 7+ volts... Volt reg fine... evrything is "nominal".... :)
Click to expand...
Grrreaat! :lol:
 
You must log in or register to reply here.

Similar threads

J
Ford 555 hydraulics fixed !
Replies
2
Views
312
Check Break
C
R
1954 Ford NAA Tapping In Top Lid
Replies
2
Views
632
JMOR
J
9
New Ford 600 owner here
Replies
14
Views
1K
92stroker
9
S
Ford 3000 - no 3 point hydraulics
Replies
4
Views
646
supton
S
M
64 Ford 2000 Hydraulic and transmission help!
Replies
1
Views
455
sunbeam
S
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top