Topic: Re: 12v conversion - now hard/no start when cold - ytmag kit
|Ford 9N, 2N & 8N Discussion Forum|
[Show Entire Topic] [Return to Forum]
[Show Entire Topic]
[Return to Forum]
[Add a Reply]
Quoting Removed, click Modern View to see
There are two resistors in the line, the OE one on the terminal block under the ammeter, and then in addition, the one that was sent with the kit. But no information in the kit as to if it should be used or not, and no info on the coil either. The website says its a 12v coil... so was a bit surprised there was a SECOND resistor they said to use in series... but their email said to use it. If I bypass the secondary resistor - leaving the OE in the line only, it started fine when cold - great actually - better than it did when 6v. But with it in as they say, its much worse than the 6v.
But just want to be sure Im not going to burn out the coil, not having any information on it other than "12 Volt coil" (from: http://www.ytmag.com/8NE10300ALTC_501.htm) and no mention of anything in the instructions about the resistor other than "IF used - wire this way" type mention.
My initial thought was to remove the second resistor (new one from the kit) which is what brought about the idea of by passing it when it wouldnt start cold. But concern for burning the coil out is what prompted me to post here. JMOR and you both are backing up my initial thoughts... that it shouldnt burn out the new coil.
Should have some good cold weather tomorrow, so leaving it out on the trailer (had it loaded to take back to dad today until it wouldnt start when I went to chain it down for the trip). Will be able to do a test in some good cold air in the morning. Only thing I cant test is how it handles hot weather :lol: and time will tell if the coil burns out I guess. But good to know my thinking wasnt too far off base.
If she starts well tomorrow like expected, Ill just make a pig tail (and make my all new and pretty re-wiring job look like a nice job with a hacked in splice :x ) and haul it back to him for "testing" :twisted:
If anyone else wants to chime in with confirmation, or other details, Ill be checking back as well as letting you know all is well.
|Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a Company you can trust and have generous return policies! Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ More Info ]|
| Copyright © 1997-2013 Yesterday's Tractor Co.|
TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
|About this site - Yesterday's Tractors is your one-stop source for antique tractors. If you are interested in older tractors you've come to the right place! Join more than 275,000 other classic tractor enthusiasts from all over the globe. We have many resources for antique tractor enthusiasts available including photos, classified ads, more than 24 tractor discussion forums, a show guide, values, specs and much more. Bookmark this site and come back often. Thanks for stopping by! Feel free to use our feedback form to send us your comments, suggestions and ideas.|