John Kamerer
New User
I just restored a 46 2N motor. Runs great, BUT after it warms up the oild pressure drops to 1 maybe 2 lbs. Starts out at 35 - 40 lbs. What gives? is the spring tension on the pressure thingy bobby up front weak?
id you do any oil pump work? Did you verify all main, rod, and cam bearing clearances?(quoted from post at 18:47:42 01/09/13) I just restored a 46 2N motor. Runs great, BUT after it warms up the oild pressure drops to 1 maybe 2 lbs. Starts out at 35 - 40 lbs. What gives? is the spring tension on the pressure thingy bobby up front weak?
a new one was installed during the over haul" new pump or new gear?(quoted from post at 19:10:44 01/09/13) The original oil pump had a striped gear to the crank. a new one was installed during the over haul. Yes all clearances were checked. I do get good oil pressure for the first 10 minutes.
learance from the gear surfaces to surfaces they run against and shaft to bore clearances as well as face to face are all critical. "Look good" isn't good enough. If bearings plasti-gauged good & good cam bearing clearances were verified, I would be suspect of oil pump.(quoted from post at 19:19:28 01/09/13) just a new drive gear the impellers were in good shape
(quoted from post at 18:47:42 01/09/13) I just restored a 46 2N motor. Runs great, BUT after it warms up the oild pressure drops to 1 maybe 2 lbs. Starts out at 35 - 40 lbs. What gives? is the spring tension on the pressure thingy bobby up front weak?
the oil filter line on the bottom goes arround the back of the block and enter the inspection cover for the valve adjusters. inside it sprays out the the valves."...........sorry, but not on an N tractor!(quoted from post at 19:45:04 01/09/13)
Looks like i need to drop the pan and check the nuts on the oil pump.. I remember tighting these as i wire the nuts. the oil filter line on the bottom goes arround the back of the block and enter the inspection cover for the valve adjusters. inside it sprays out the the valves. I thought this was letting to much oil pass thru. So, I installed a shut off valve in the line and as i close the valve I can get oil pressure up to 10 lbs but then I hear increasing valve noise.
(quoted from post at 20:20:40 01/09/13) Yep it's what it does. I've not seen this before either. But, who knows what some users do when they try to fix things. The govenor does not have a oil inlet. Do I need to install one and run the oil line there? The casting on the block shows B116 which I think means a Feb 11, 1946 engine. I got this out of Kamloops BC for $500 and it had almost new tires all around. but the engine was siezed up. I restored an 8N 3 yrs back with all your help on the forum.
(quoted from post at 17:29:10 01/09/13)(quoted from post at 20:20:40 01/09/13) Yep it's what it does. I've not seen this before either. But, who knows what some users do when they try to fix things. The govenor does not have a oil inlet. Do I need to install one and run the oil line there? The casting on the block shows B116 which I think means a Feb 11, 1946 engine. I got this out of Kamloops BC for $500 and it had almost new tires all around. but the engine was siezed up. I restored an 8N 3 yrs back with all your help on the forum.
A farmerization that probably breaks things and possibly why you had a siezed engine. That oil line flow is inline with the mains/rods and is sucking off pressure. Remove that kludge - the valves do not need it and it only confuses the issue.
I'll drill and tap a 1/8th NPT in the governor and move the line there. The oil does need to return form the oil filter right?
TOH
(quoted from post at 20:35:04 01/09/13)/quote]If I follow your oil line description correctly.........then what has been done is that the oil filter outlet (bottom center) has been routed into the valve cover instead of into the governor (or as before the governor oiling scheme, into the block(see pic), just below the filter. I would want it corrected, too, but I'm afraid this (where oil filter return dumps) will NOT impact your low oil pressure.(quoted from post at 17:29:10 01/09/13)(quoted from post at 20:20:40 01/09/13) Yep it's what it does. I've not seen this before either. But, who knows what some users do when they try to fix things. The govenor does not have a oil inlet. Do I need to install one and run the oil line there? The casting on the block shows B116 which I think means a Feb 11, 1946 engine. I got this out of Kamloops BC for $500 and it had almost new tires all around. but the engine was siezed up. I restored an 8N 3 yrs back with all your help on the forum.
A farmerization that probably breaks things and possibly why you had a siezed engine. That oil line flow is inline with the mains/rods and is sucking off pressure. Remove that kludge - the valves do not need it and it only confuses the issue.
I'll drill and tap a 1/8th NPT in the governor and move the line there. The oil does need to return form the oil filter right?
TOH
(quoted from post at 20:35:04 01/09/13)I'll drill and tap a 1/8th NPT in the governor and move the line there. The oil does need to return form the oil filter right?(quoted from post at 17:29:10 01/09/13)(quoted from post at 20:20:40 01/09/13) Yep it's what it does. I've not seen this before either. But, who knows what some users do when they try to fix things. The govenor does not have a oil inlet. Do I need to install one and run the oil line there? The casting on the block shows B116 which I think means a Feb 11, 1946 engine. I got this out of Kamloops BC for $500 and it had almost new tires all around. but the engine was siezed up. I restored an 8N 3 yrs back with all your help on the forum.
A farmerization that probably breaks things and possibly why you had a siezed engine. That oil line flow is inline with the mains/rods and is sucking off pressure. Remove that kludge - the valves do not need it and it only confuses the issue.
TOH
(quoted from post at 21:37:34 01/09/13) Thanks for the pic. I'll run it to the block as shown. But I agree it won't help the oil pressure. or is there a good reason they went to the govenor?
(quoted from post at 09:57:03 01/10/13) Thanks, that's reassuring . I'm still going through a few steps to fix it. The previous owner had the oil line at the bottom of the filter going into the valve adjusting side plate to spray the lifters. I'm thinking that enough oil stayed up on that ledge to cause low oil level in the pan. It's a thought. I'm rerouting the line today to the block to,test and then I'll run it to the govener. Let everybody know the results
It is such a great help to get all that knowledge laying out there in the world of Internet .
(quoted from post at 19:39:38 01/10/13)(quoted from post at 09:57:03 01/10/13) Thanks, that's reassuring . I'm still going through a few steps to fix it. The previous owner had the oil line at the bottom of the filter going into the valve adjusting side plate to spray the lifters. I'm thinking that enough oil stayed up on that ledge to cause low oil level in the pan. It's a thought. I'm rerouting the line today to the block to,test and then I'll run it to the govener. Let everybody know the results
It is such a great help to get all that knowledge laying out there in the world of Internet .
Got the oil line ran to the govenor. Started up with 30 lbs of oil pressure. after 10 minutes went down to 15 and the after 15 min droped to 10. 20 mins it was down to 5. Rev it up to half throttle and it raised to 15. did this a few times. And then at idle would show 2-3 lbs. Rev it and it would come back to 10-15 Lbs. So, whats the thoughts out there?
(quoted from post at 16:39:38 01/10/13)(quoted from post at 09:57:03 01/10/13) Thanks, that's reassuring . I'm still going through a few steps to fix it. The previous owner had the oil line at the bottom of the filter going into the valve adjusting side plate to spray the lifters. I'm thinking that enough oil stayed up on that ledge to cause low oil level in the pan. It's a thought. I'm rerouting the line today to the block to,test and then I'll run it to the govener. Let everybody know the results
It is such a great help to get all that knowledge laying out there in the world of Internet .
Got the oil line ran to the govenor. Started up with 30 lbs of oil pressure. after 10 minutes went down to 15 and the after 15 min droped to 10. 20 mins it was down to 5. Rev it up to half throttle and it raised to 15. did this a few times. And then at idle would show 2-3 lbs. Rev it and it would come back to 10-15 Lbs. So, whats the thoughts out there?
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2024 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy