Yesterday's Tractor Co. Shop Now
   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
Classified Ads
Photo Ads
Tractor Parts

Discussion Forums
Project Journals
Tractor Town
Your Stories
Show & Pull Guide
Events Calendar
Hauling Schedule

Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs

Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

Related Sites
Tractor Shed
Ford 8N/9N Club
Today's Tractors
Garden Tractors
Classic Trucks
Kountry Life
Ford 9N, 2N & 8N Discussion Forum
Show Parts for Model:

Re: No oil to rocker arm shaft top for valve tappets

[Show Entire Topic]  

Welcome Guest, Log in or Register
Author  [Modern View]

11-16-2012 05:45:30

Report to Moderator

There are no cam bushings in a 134 ci engine in the Ford tractor

I suspect that the bottom of the oil tube is not in the hole in the oil gallery down on the block over the camshaft.

Even when everything is installed correctly the oil supply to the rocker arms is a pulsating supply because the oil only gets into the tube when the cam shaft turns to the place with the oil gallery lined up with the hole in the block.

I would try blowing through the tube with air and also make sure the opening in the oil gallery is not blocked by crud.


[Log in to Reply]   [No Email]
Den N Ms

11-16-2012 08:06:43

Report to Moderator
 Re: No oil to rocker arm shaft top for valve tappets in reply to ZANE, 11-16-2012 05:45:30  
There are no cam bushings in a 134 ci engine in the Ford tractor.

Did it have new cam bearings installed in the block?

I know that they did not come with cam bearings,but It could have them now after 59 years and numerous rebuilds.

[Log in to Reply]  [No Email]

11-17-2012 18:04:12

Report to Moderator
 Re: No oil to rocker arm shaft top for valve tappets in reply to Den N Ms, 11-16-2012 08:06:43  
I've been working on Ford tractors since I was 15 years old and have never seen one with cam bearings new or old???? I am now 77.


[Log in to Reply]  [No Email]
[Show Entire Topic]     [Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:

Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

Home  |  Forums

Copyright © 1997-2018 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters