Yesterday's Tractor Co. New Parts for Old Tractors
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads

Community
Discussion Forums
Project Journals
Tractor Town
Your Stories
Show & Pull Guide
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

Related Sites
Tractor Shed
TractorLinks.com
Ford 8N/9N Club
Today's Tractors
Garden Tractors
Classic Trucks
Kountry Life
Enter your email address to receive our newsletter!

subscribe
unsubscribe
  
Discussion Forum
Show Parts for Model:

Re: Crankshaft Pulley

[Show Entire Topic]  

Welcome Guest, Log in or Register
Author  [Modern View]
John Smith8N

11-06-2012 20:11:53
75.23.122.73



Report to Moderator

Quoting Removed, click Modern View to see

I've got one of those handy dandy installation tools, but if the bore in the replacement pulley is actually .003" smaller than the crank snout like they're sayin', it ain't gonna pull it on there. It would go on half way and gall up, or it would crack the pulley snout. That's too much of a press fit.
One big difference in the small block Chevy balancer old Boxwrench is installing and the N tractor pulley is the keyway. The small block Chevy balancer can start on the key before you start pulling it on. The N tractor pulley just has a little slot right at the end of the pulley snout and a short key inside at the timing gear. If you can eyeball that key, then pull that tight fitting pulley all the way on the crank and have it drop dead nutz onto the key when it gets there, you're dayum good. Especially with the timing cover on so you can't see how it's going. You'd have to be magical. No backyard Bob is gonna pull that off, and very few pros, either.

[Log in to Reply]   [No Email]
[Show Entire Topic]     [Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:

TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ More Info ]

Home  |  Forums


Copyright © 1997-2014 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters