Yesterday's Tractor Co. Affordable Parts, Just in Time
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Tractor Manuals
Tractor Parts
Classified Ads
Photo Ads

Community
Discussion Forums
Project Journals
Tractor Town
Your Stories
Show & Pull Guide
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

Related Sites
Tractor Shed
TractorLinks.com
Ford 8N/9N Club
Today's Tractors
Garden Tractors
Classic Trucks
Kountry Life
Enter your email address to receive our newsletter!

subscribe
unsubscribe
  
Ford 9N, 2N & 8N Discussion Forum
Show Parts for Model:

Re: stubborn 8N

[Show Entire Topic]  

Author  [Modern View]
Bruce (VA)

10-18-2012 06:45:04
24.125.80.178



Report to Moderator

There are two schools of thought when it comes to getting a non-running tractor to start. One way is to just start replacing every part you can get to until it starts or you run out of money. The other way is to take a step-by-step approach to solving the problem, working from most likely to least likely. The trick to fixing these tractors (or trouble shooting any piece of equipment) is to be systematic about it. You need to isolate the problem step by step and work from most likely to least likely. You have solved half the problem by determining it is a spark problem. As others have just said, that doesnít mean you need to replace all of the electrical parts on the tractor!

I'll save you some money......it's highly unlikely that you have a bad coil or condenser. What you do have is poor troubleshooting skills. We can help w/ that.

Before you check anything else, make sure you have the correct voltage at the top of the coil. It should be battery voltage w/ the points open & about half that w/ the points closed.

Assuming that the bushings & advance weights are ok, & that you have correct voltage to the coil, the most common electrical failure (no spark, weak spark) points on the frontmount are:

1. The insulator under the brass concave head screw & where the copper strip attaches. (itís fiber & will wear out; poke & prod w/ your meter leads to make sure it still works)

2. The pigtail at the bottom of the coil not making contact w/ the concave head brass screw inside the distributor. (With the coil on, the pigtail must firmly contact the brass screw. No contact = no spark.).

3. The copper strip is broken or grounded to the plate. (look very carefully for cracks & breaks)

4. The condenser wire grounding to the plate or side of the distributor.

5. The tab on the bottom of the coil not making contact w/ the brass button on the cap. (With the cap on, the tab must firmly contact the brass button. No contact = no spark.)

6. Incorrect positioning of the spring clip on the plate causing the pigtail to ground. (the open part of the clip goes between 7 & 9 oíclock on the plate. That puts the straight part of the clip opposite of the timing screw at 3 oíclock)

7. Incorrect seating of the coil on the distributor due to a loose bail or no gasket.(the coil must not move at all; if it does, replace the gasket or bail. Or stick some cardboard under the bail).

8. Water/moisture inside the cap due to gasket failure or the absence of a gasket. (the cap AND coil have gaskets)

9. Dirty/corroded/burned/incorrectly gapped or misaligned points.

10. Burned rotor, cracked/carbon tracked cap.

Unless the coil is cracked or shows a dead short, chances are it's fine; square coils rarely fail cold. Pull the distributor & do a continuity check.

First, make sure your meter/light works (don't ask....)

You can change points everyday & it will not fix bad bushings. If you are having trouble w/ points failure, check the shaft. If you detect movement, chances are it needs new bushings.

Inspect the points; if they are pitted or burned, replace them. Next, dress the points by running a piece of card stock or brown paper bag through them. New points sometimes have an anti-corrosive dielectric coating on them & old points can corrode or pick up grease from a dirty feeler gauge or excessive cam lubricant. Make sure the points align correctly. Proper alignment is also critical to longevity. Look at the points when they are closed; both sides should mate evenly. Then, check the gap at .015 on the high point of all 4 cam lobes.

Now, follow these steps:

1. Coil off, cap off, points open. One probe on the brass screw & the other on both sides of the open points. On the side closest to the cam, you should have continuity. Not on the other side! If you do, you will also have continuity everywhere because the points are grounded.

2. Coil off, cap off, points open. One probe on the brass screw & the other anywhere on the body of the distributor. You should have no continuity! Now, rotate the tang on the distributor....as the points open & close, you have continuity (closed) and lose it when they open.

3. Coil on, cap off, points open. One probe on the lead on the top of the coil, the other on the cam side of the open points. You should have continuity!

4. Coil on, cap off, points open. One probe on the lead on the top of the coil, the other anywhere on the body of the distributor. You should have no continuity!

At this point, I just put the distributor, coil & cap all back on the tractor as a unit. The reason I do this is because it is real easy to get the cap or coil mis-aligned trying to put it back together one piece at a time & the result is something gets broken or you get a Ďno sparkí problem.

It's possible to put it back on wrong & break it. Look at the slot on the end of the cam shaft. What ever angle it happens to be, turn the distributor tang to match it. Make sure you can tell the wide side from the narrow side on both the cam & distributor! (close counts) Then place the distributor on the front of the engine, gently push it in place & slowly turn the distributor body until you feel the tang slip into the slot. Rotate the distributor body until the bolt holes line up. Then, hand tighten the two bolts until the distributor body is flush w/ the timing gear cover.

Finally, double check your firing order & plug wires. Itís 1-2-4-3, counterclockwise. Itís very easy to cross 3 & 4.

Post back w/ answers to our questions; we can help you get it running.

[Reply]   [No Email]
sootman2

10-23-2012 20:34:11
75.104.160.54



Report to Moderator
 Re: stubborn 8N in reply to Bruce (VA), 10-18-2012 06:45:04  
Having never contributed to the forum before, I wasn't sure how to reply back to my advisors. So I'll just post this way and see if it works; to Royse, old tanker, and BruceVA: Thanks for the excellent tips. I was more than a little embarrassed to be labeled a poor troubleshooter, after being an aerospace ground equipment mechanic in the AF for 9 years, but it is true. This little tractor has some weird habits, and I am no expert on it, for sure. I did tune it up because it needed it, so I don't think I bought unnecessary parts. Yes Royse, when I looked at the parts catalog, I made sure I got the same ballast resistor listed for my tractor, and the only reason I suspected it might be an issue was that the bakelite was crumbling so bad that it was hard to keep nuts tightened down on the screws. I had already checked the switch, but when I moved on to the coil (it's a 6 v) it had batt voltage. It had battery voltage at the condenser and points connection to the brass screw. Points open or closed, so checked the housing; same thing. I didn't think I would get battery voltage if it was grounded out, but here was my evidence. So checked out the insulator that Bruce had suggested might be worn out at the brass screw, and it is crumbling, so consequently shorting out. So what now? The breaker plate looks like a part that has to be remanufactured, but not in a home shop. The shop manual (I bought the I&T one when I bought my tractor, along with the N's operators manual published by Ford) has the breaker plate PN as 9N12151, and all I could find in ytmag was PN 9N12150 and says it's for all 8N's with a front mounted distributor. From what I could tell, they are the same; not sure why they are different by one. Another question within a question; there's an electronic ignition conversion that would fit in this distributor; does it need that insulated connection, or would it bypass it; I am not familiar with how they hook up? I think I'm going to hold off on ordering the breaker plate until I hear back from one of you guys. Thanks again for your tips. By the way, oltanker's tip to get Bruce's 50 Tips was a good one; first thing I did when I got your replies was to print them off and put them with my manuals.

[Reply]  [No Email]
Bruce (VA)

10-24-2012 06:28:39
24.125.80.178



Report to Moderator
 Re: stubborn 8N in reply to sootman2, 10-23-2012 20:34:11  
" So what now?"

Replace the insulator w/ a square nylon anchor nut. Check out the link below.

" It had battery voltage at the condenser and points connection to the brass screw. Points open or closed, "

Which means you have a dead short, as I said in my continuity check list.

If you do not want to try replacing the insulator, just replace the entire plate for $35 or so. But save the concave head brass screw because the replacement plates do not come w/ them.

"Another question within a question; there's an electronic ignition conversion"

Why? You can fix it w/ the nylon anchor for $1. And quality points correctly installed. EI will not work well at all on 6v (it won't fire below 5.2v) so you would need to convert it to 12v.

EI does not give you higher spark voltage, eliminate all maintenance on your ignition system or give enough of a horsepower boost to cause the tractor to do wheelies. It replaces the points. Thatís it. It will not correct or overcome other problems in the ignition system. While it may give you more HP or improve fuel economy, both would be so insignificant as to be hardly noticeable on a 23 hp engine. If you canít set points or donít care to do it, or you donít want to spend the 30 minutes or so a year to check the gap & lube the cam, then you will be happy w/ EI. And, the EI unit itself will be maintenance free. (but the rest of the ignition system wonít) You will spend probably $235 for an EI kit & 12v conversion. If you install them correctly you will have an easy starting tractor for a long time. And, the 12 volt conversion & EI will have just about nothing to do w/ the good performance. What will make the real difference is the new wiring, cables, clean grounds & new battery.

The key advantage to EI is that you do not need to gap & lube the points every year & replace them every 4 or 5 years or. If you perform annual maintenance on the points & change them every 4 years or so using quality parts, you will see no difference whatsoever between a points ignition system & EI on an N.

The key disadvantages to EI on an N are initial cost, nearly impossible for the average N owner to repair, will not work w/ low battery voltage, & easily damaged beyond repair by polarity reversal & other common mistakes.

Bottom lineÖÖÖ.this is the question you need to answer: ďIf tens of thousands of other Nís operate just fine on 6v and points, why canít mine?Ē

Your money, your tractor, your call........$1 or $240.

Please post back w/ results or other questions.

[Reply]  [No Email]
sootman2

10-24-2012 10:48:56
75.104.160.36



Report to Moderator
 Re: stubborn 8N in reply to Bruce (VA), 10-24-2012 06:28:39  
I had read enough, and had my 8N long enough, to know that I didn"t necessarily need a 12 volt system. I used to have a Ferguson TO-30, converted to 12v before I got it, and didn't notice that it started any easier or ran better than either of the Ns that I've had. And to know that I can fix the breaker plate with just a nylon nut means I can probably get this thing going this week (and I'm cheap enough that I won't spend $35 or $42 or whatever over a buck or two). I've been dinking around with old cars for over 50 years; when I had my first paid for car, it still was put together and kept running with help from local junkyard, so old ignition systems aren't exactly foreign; changing out points and distributor parts will just keep me in practice. And to know I have good help on this site, that much better. Thanks for your help and prompt reply.

[Reply]  [No Email]
[Show Entire Topic]     [Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Add a Reply]

Hop to:
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ More Info ]

Home  |  Forums


Copyright © 1997-2014 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters