| Ford 9N, 2N & 8N Discussion Forum |
Topic: 1948 Ford 8N Tractor
[Return to Forum]
| Author |
[Modern View]
|
| lee norris
09-26-2012 08:30:57
97.123.220.36
|
Dear Sirs:I have a question. I am restoring the 1948 8N and need to know what 6V original generator and pulley diameter applies. I have the original 3 wire harness. Your response would greatly be appreciated. Thank you. Lee
|
|
|
| JMOR
09-27-2012 06:19:17
72.181.173.171
|
|
Re: 1948 Ford 8N Tractor in reply to douglloyd, 09-26-2012 08:30:57
|
|
| Quoting Removed, click Modern View to seeBob, so, if original, your generator should be 8N10000A, identified by a HI/LO adjustment screw on rear bearing plate, a 3rd brush which may have been removed as per an Oct, 1948 Service Bulletin, and it may have a barrel length (between the end plates) of 5 1/2 inches with some possibility of 6 1/8 inch length. Be interested in your response. Thanks.
|
|
|
| JMOR
09-26-2012 14:49:23
72.181.173.171
|
|
Re: 1948 Ford 8N Tractor in reply to bgarrett, 09-26-2012 08:30:57
|
|
| Quoting Removed, click Modern View to see1948 is not enough info to identify which generator it would have left the factory with. It could have been 8N10000A (through serial #137684) or 8N1000B(serial #137685 thru #263843).
|
|
|
| Bob Purinton
09-26-2012 13:55:57
74.38.200.241
|
|
Re: 1948 Ford 8N Tractor in reply to lee norris, 09-26-2012 08:30:57
|
|
| I went out and looked on my '48 8N and measured my 3 wire genny pulley. Jackinok is correct at 3.5 inches across the pulley.
|
|
|
| Bob Purinton
09-26-2012 18:16:32
74.38.200.241
|
|
Re: 1948 Ford 8N Tractor in reply to Bob Purinton, 09-26-2012 13:55:57
|
|
| My 1948 8N is SN = 8N 131343
|
|
|
| jackinok
09-26-2012 09:19:35
162.58.82.136
|
|
Re: 1948 Ford 8N Tractor in reply to lee norris, 09-26-2012 08:30:57
|
|
| i do not have my part books here, but look in the parts section of this site.you could probably find what you need to know there, as far as the generator goes,maybe not the pulley diameter though. for some reason 3 1/2 " comes to mind but i could be wrong.
|
|
|
[Options]
[Printer Friendly]
[Return to Forum]
[Add a Reply]
| Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a Company you can trust and have generous return policies! Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ More Info ] |
Home
| Forums
Copyright © 1997-2013 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor Headquarters |
About this site - Yesterday's Tractors is your one-stop source for antique tractors. If you are interested in older tractors you've come to the right place! Join more than 275,000 other classic tractor enthusiasts from all over the globe. We have many resources for antique tractor enthusiasts available including photos, classified ads, more than 24 tractor discussion forums, a show guide, values, specs and much more. Bookmark this site and come back often. Thanks for stopping by! Feel free to use our feedback form to send us your comments, suggestions and ideas.
|
|
