Author	[Modern View]
msgove 09-24-2012 08:06:05 173.9.60.221 Report to Moderator	Has anyone replaced the studs that screw into the bearing housing on the rear hubs, and that then slip through the holes on the axle housing? I tried to replace these studs with auto studs from the hardware store, but when I went to reinstall the hub and axle, the studs did not line up with the holes on the axle housing, and some of them looked like they were not straight, so I was concerned that they were not the right quality and had bent when being installed. Any ideas where I should get replacements? [Reply]   [No Email]
Hobo,NC 09-25-2012 09:42:25 98.17.83.160 Report to Moderator	Re: Studs in reply to Mr. T. Minnesota, 09-24-2012 08:06:05   I worked on a 9N were someone bolted a few of'em... It was a mess so I helicoiled and replaced with used studs... [Reply]  [No Email]
boler76 09-25-2012 04:29:26 184.151.63.216 Report to Moderator	Re: Studs in reply to msgove, 09-24-2012 08:06:05   are you sure the shoulder on the new stud isnt larger OD than the original bolt OD ? [Reply]  [No Email]
msgove 09-25-2012 06:16:24 173.9.60.221 Report to Moderator	Re: Studs in reply to boler76, 09-25-2012 04:29:26   Yes. I don't recall the exact measurements at the moment (I'm at work), but they were identical. Plus, I was able to screw the new bolt into the bearing housing without any problems. [Reply]  [No Email]
Dean 09-24-2012 12:30:19 152.216.3.5 Report to Moderator	Re: Studs in reply to msgove, 09-24-2012 08:06:05   Have you checked CNH? Dean [Reply]  [No Email]
TheOldHokie 09-24-2012 08:23:56 108.8.18.102 Report to Moderator	Re: Studs in reply to Hobo,NC, 09-24-2012 08:06:05   Quoting Removed, click Modern View to see Highly unlikely. How would you bend them? And why are you replacing them? I'm guessing one or more of them are cross threaded. TOH [Reply]  [No Email]
Bob Harvey 09-24-2012 08:15:19 209.91.107.209 Report to Moderator	Re: Studs in reply to msgove, 09-24-2012 08:06:05   Have you checked "Tractor Parts" on this site ? [Reply]  [No Email]
msgove 09-24-2012 11:07:09 173.9.60.221 Report to Moderator	Re: Studs in reply to Bob Harvey, 09-24-2012 08:15:19   Yes, and these studs are not there. They are also one of the few parts NOT identified by part number in the FO-4 service manual. [Reply]  [No Email]
carolina don 09-24-2012 13:25:00 70.60.100.86 Report to Moderator	Re: Studs in reply to msgove, 09-24-2012 11:07:09   Just checked.....YT does have. don b [Reply]  [No Email]
msgove 09-24-2012 13:36:42 173.9.60.221 Report to Moderator	Re: Studs in reply to carolina don, 09-24-2012 13:22:37   I don't think that's it -- here's a picture of what I'm trying to replace. The old one taken off the tractor is on the left (with the nut still attached), the new one that I tried to replace it with is on the right. Picture of studs [Reply]  [No Email]