Author	[Modern View]
boler76 09-23-2012 16:53:49 184.151.61.146 Report to Moderator	I have acquired a 9n with an 8N motor that isnt complete. What I need to know is what is the part# for the support bracket that holds the horizontal throttle shaft on the front of the head, It goes on with the head bolts and has the pivot and the spring attachment point? Can someone point me to the right part, Cant find it in the parts book, probably because not looking in the right place. Thanks in advance [Reply]   [No Email]
Royse 09-24-2012 08:32:38 68.77.236.5 Report to Moderator	Re: throttle shaft support in reply to Bruce (VA), 09-23-2012 16:53:49   Clear to me! It just didn't look like it would be a direct fit to the 8N's more vertical linkage. Might as well get all the parts in one order! :) [Reply]  [No Email]
GB in MT. 09-24-2012 07:59:09 216.14.236.18 Report to Moderator	Re: throttle shaft support in reply to oldtanker, 09-23-2012 16:53:49   Royse said: (quoted from post at 20:26:37 09/23/12) Will that linkage hook up and work on an 8N governor? I've never tried it, just asking. Royce; Short answer is:......YES & NO!!!! :lol: I'm using an early, 8N-A GOV, on my 2N.....BUT.... the throttle rod to Gov., assy. arm.....pt.# 8N-18190, has to be replaced with, the 9/2N assy. arm...pt.#9N-18190. The hook-up for the down pointing throttle rod to Gov. at the Gov arm...for the 9/2N.... has a hook-up point that is lower than the 8N's. He will have to have the 9/2N assy. gov. arm, to make it work right. Change that out and it should work fine!! Mine does!!!??? Clear as mud....RIGHT??????? :lol: Gary :roll: BTW:......Where I said,....an early, 8N-A distrib.,......was supposed to read, 'early 8N-A GOV......and now has been changed......DUH..... :? This post was edited by GB in MT. at 19:01:46 09/24/12. [Reply]  [No Email]
Royse 09-23-2012 18:26:37 69.36.49.151 Report to Moderator	Re: throttle shaft support in reply to Mr. T. Minnesota, 09-23-2012 16:53:49   Will that linkage hook up and work on an 8N governor? I've never tried it, just asking. [Reply]  [No Email]
Jim.UT 09-23-2012 18:18:36 207.50.149.181 Report to Moderator	Re: throttle shaft support in reply to boler76, 09-23-2012 16:53:49   GB is correct. I was able to find a weak wifi connection. I do have some of those. There are two different designs. The earlier design is made of cast iron and the later design is stamped steel. I have both. I can send pics of both if you will email me so I have your email address. I won't be home until Tuesday night sometime. I won't be able to send pics until probably Wednesday night at the soonest. [Reply]  [No Email]
GB in MT. 09-23-2012 18:05:58 216.14.236.18 Report to Moderator	Re: throttle shaft support in reply to Promo III, 09-23-2012 16:53:49   Quoting Removed, click Modern View to see Boler; Del H., has the right part#, and I just called and talked with Jim UT.!!!! He said that he has a couple of those in his parts bins, but he is out of town for a couple of days. He ask me to give you his email addy, so you can EMAIL HIM. email addy....: webbtractor@gmail.com. HTH Gary :) [Reply]  [No Email]
Del Huebner 09-23-2012 17:46:49 173.18.13.41 Report to Moderator	Re: throttle shaft support in reply to boler76, 09-23-2012 16:53:49   Is this the bracket you are looking for. I think the part is 9N 9824-A2 but I don't think its available only maybe a used one. [Reply]  [No Email]