Yesterday's Tractor Co. Shop Now
   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
Classified Ads
Photo Ads
Tractor Parts

Discussion Forums
Project Journals
Tractor Town
Your Stories
Show & Pull Guide
Events Calendar
Hauling Schedule

Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs

Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

Related Sites
Tractor Shed
Ford 8N/9N Club
Today's Tractors
Garden Tractors
Classic Trucks
Kountry Life
Discussion Forum
Show Parts for Model:

Cab adjustment for high RPMs

Welcome Guest, Log in or Register
Author  [Modern View]

09-18-2012 07:45:34

Report to Moderator

Hi All, so I got the spark issues resolved on my '52 8N sidemount only to find carb issues. Float was bad (it was a sinker), so got a rebuild kit and a new float went through the carb rebuild page on this site and did as instructed and cleaned out all the passages (many were plugged up bad), and got everything nice and clean.
I put it all back together, bolted it on, and it fired right up. Low RPM adjustment is perfect. The engine idles very nicely at a low RPM. The proofmeter does not work but I am guessing 400 rpms. Its nice and slow. I never heard an 8N idle so smoothly at such a low RPM.

My problem is with high RPMS. With no load, it will rev up nicely at full throttle. Under load, at full throttle, it sputters and will not run smooth. I am certain the main jet was clear when I put it back together. The old main jet needle is shorter than the one in the rebuild kit. Maybe as much as 1/8". I tried the new (longer) needle first, and had trouble getting smooth RPM at full throttle and no load - I had to screw it out until it was loose. The old (shorter) needle works good at high RPM with no load, but I get sputterin' when I put any load at the engine (it drives jerky at full throttle). Is it getting richer or leaner as I screw out the main get? I believe it is getting richer, but not rich enough under load? Or is it too rich?

This post was edited by ChrisCos at 07:46:44 09/18/12.

[Log in to Reply]   [No Email]

09-18-2012 07:58:15

Report to Moderator
 Re: Cab adjustment for high RPMs in reply to Bruce (VA), 09-18-2012 07:45:34  
Thanks Gary. 1/16th of a turn... that is part of my problem. I was making half turn adjustments. Looks like more finesse is needed :)

Will post back after I fiddle with it tonight.

[Log in to Reply]  [No Email]

09-18-2012 11:34:00

Report to Moderator
 Re: Cab adjustment for high RPMs in reply to ChrisCos, 09-18-2012 07:58:15  
sure does sound lean

[Log in to Reply]  [No Email]
GB in MT.

09-18-2012 07:54:19

Report to Moderator
 Re: Cab adjustment for high RPMs in reply to Dave/MO, 09-18-2012 07:45:34  


Try this set up sheet.......Post back if this does not work for ya!!!, or more help is needed!!!

Gary :)

[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:

Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

Home  |  Forums

Copyright © 1997-2018 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters