(800) 853-2651
SHOP NOW

MM 602 Hydraulic Issue

J

Jon Pedigo

Member
Hooked up a disc mower on my 602, the 3 point is just fine, it'll pick up the disc mower no problem. But when i went to hook up the hydraulic line i wasn't getting any fluid out of the tractor. The hose shakes when i move the lever like its trying to do something but i wasn't getting anything out. I checked my levers on my hoses and i believe they are all good. Do the levers under the seat have anything to do with the hoses? Right now they are pointed to the right? The tractor has been completely restored but i cant remember hooking anything up to the hydraulic lines in 5 years or so. Would this be a pump issue even with the 3 point working just fine? Or possibly some crud in the hose on the tractor. Don't know of any ways to check the hydraulics to narrow down the problem so any advice is much appreciated
 
Maybe the coupler (tractor or implement side) is bad. It seems pretty common for me to have to put new pioneer ends on some things every now and then. If the short hose to the coupler moves like it has pressure to it something you can do is loosen the female coupler just a bit then move the lever just a little and see if it will leak a little that will tell you if you are getting oil that far. You will then know if its a hyd system problem or a plumbing issue. If the hyd hoses haven been hooked up in a while i can sure see the coupler sticking
 
Agree Blake. Had the same problem on my 4Star. Drove me
nuts until I figured it out. Thankfully didn't dig into anything
serious before I tried that.
 
If it was my m5, and I am assuming your 602 has the same hydraulic lift, the first thing I would do is remove the plate that has the 2 levers in it and check the fluid level. It should be about 1" below that plate when the lift is down and all installed cylinders are retracted.
 
You must log in or register to reply here.

Similar threads

Tgrasher
Preserving hydraulic hoses, floating an idea
2
Replies
32
Views
2K
Janicholson
Janicholson
G
Need hose that goes from hydraulic tank to hydraulic motor on 1980 Ford 445 diesel
Replies
2
Views
132
gnc23
G
R
oliver 550 hydraulic issue
Replies
1
Views
218
89 MJ
89 MJ
C
M-602 to tractor show in area
Replies
2
Views
376
cleddy
C
M
  • Question
Oliver 550 Hydraulic issue
Replies
6
Views
279
msellers
M
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top