Yesterday's Tractor Co. Low Prices, Parts Ship Fast!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Tractor Manuals
Tractor Parts
Classified Ads
Photo Ads

Community
Discussion Forums
Project Journals
Tractor Town
Your Stories
Show & Pull Guide
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

Related Sites
Tractor Shed
TractorLinks.com
Ford 8N/9N Club
Today's Tractors
Garden Tractors
Classic Trucks
Kountry Life
Enter your email address to receive our newsletter!

subscribe
unsubscribe
  
Minneapolis Moline Tractors Discussion Forum
Show Parts for Model:

Re: MM705 Split

[Show Entire Topic]  

Welcome Guest, Log in or Register
Author  [Modern View]
glgrumpy

01-20-2013 11:29:20
50.129.205.26



Report to Moderator

If a wide front, make sure to put blocks of wood or ? on each side of front axle pivot. If you don't the whole engine section will flop over to one side and possibly all the way to floor! Almost did that on my R MM first time pulling apart. I wedged blocks of wood in that space and hose clamped them a couple of times to hold in place. worked good. Use some long bolts/studs used in place of couple case bolts to glide it off and especially back on to line stuff up and go thru seals and bearings good. Studs can be up to 12" long and should be big, same size as the case bolts. Looking at 1/2 to 5/8" I assume. They wont hold tractor up, just act as a guide. Hope you have good upper support, don't rely on rafters in garage to hold!

[Log in to Reply]   [No Email]
bill from scotland

01-20-2013 13:00:49
81.131.121.83



Report to Moderator
 Re: MM705 Split in reply to glgrumpy, 01-20-2013 11:29:20  
I have built an angle iron frame with a four wheel trolly that sits on top of the upside down angle. I have also built in an adjustable jacking system that allows me to adjust it to the underside height of the tractor. All of this should allow me to support and slide back either the front or the rear of the tractor, the other half will have the wheels blocked and a static lifting jack to keep it supported.

[Log in to Reply]  [No Email]
[Show Entire Topic]     [Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:

TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ More Info ]

Home  |  Forums


Copyright © 1997-2014 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters