(800) 853-2651
SHOP NOW

Need Super 101/Chrysler Manifold

B

blueridge

Member
Location
Crawfordsville In
Still Need new or good manifold for my 1940 Super 101 Massey with a Chrysler engine with Intake & Carb. on bottom. It is the smaller block, with exhaust coming out the front on top. Casting # on Manifold is 612473-1. Is anyone making reproductions of these?
Gene Norman 765-362-5031
 
Remember some early Massey combines had Chrysler engines too, may be the same manifold. What are you driving this summer at the Rockville Bridge tour? I'll be driving the MF 85 diesel again. Rich
 
Hi Rich. As of now i don't think i will go on the Covered Bridge Drive this year, seems like the fun was gone out of it for me after 12 years, i enjoy the one day drives we do around here, we had 5 of them last year and did not have to load a tractor, just went to a different small town for lunch.
Been looking for manifold for several years now mine is patched up, still working, but would like to have a good one. Gene
 
Darn, we'll miss you! I've made every drive too, have been getting a few more friends going now also. Was even thinking of DRIVING the Massey the 300 mile round trip to Rockville this year instead of hauling it! LOL Not too smart, am I. About your manifold, I remember Chrysler made 217, 230, and 265 cube sixs. What size is yours? I know the 265 is longer, but will the 217 and 230 interchange? I will get to Hein and son salvage soon, I'll see if they have any.
 
I have 2 of the 101 Super parts tractors and might be a good manifold on one or both. Send your email address and I will take a look at them and get back to you. Both tractors have the original short engines. I also have a manifold off of a combine but it is the longer version.

Bob
 
You must log in or register to reply here.

Similar threads

R
MF 135 sucking through exhaust
Replies
10
Views
590
used red MN
U
R
MF 135 sucking through exhaust
Replies
0
Views
237
Reddoggy
R
M
Manifold replacement issue
Replies
10
Views
216
HFJ
H
S
IH 574 exhaust manifold problems
Replies
5
Views
434
Fritz Maurer
F
stevieb49829
Help identify a Continental l-head in a Clark forklift
Replies
4
Views
242
stevieb49829
stevieb49829
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top