(800) 853-2651
SHOP NOW

165 transmission

N

notebook

Member
I have a Massey 165 with a multipower tranny we had a remain
seal go out on the motor and when we split the tractor we also
found that the input shaft seal to the transmission was bad
also. We odered the parts and everything was fine until we went
to put the bushing over the seal for the tranny the bushing was
way to small but the seal was right we used the the bushing
that was in the book 511825M1 but it is not right. Dos anyone
know the right part number? The seal number in 886673M1
and the sn for the tractor is 9A30617. Any help would be very
appreciated the dealer is along way out and the wife is getting
mad.
 
Your tractor has the early "bushed" housing. These original sized and/or oversized bushings were never available here in Australia, but, according to to the AGCO website, were an option where you are.
The only option we had when the bush was worn out, was to replace the complete input housing, with the later version with the "needle roller" bearing and later seal fitted.
The part number for the housing is 1860 889M1 with the seal 1860 867M2.
This will upgrade your existing input housing to the later serviceable arrangement.
hope this helps, Evan.
 
Will this part work for the independant PTO or is this for the live PTO? My tractor is the IPTO. Thanks for the help.
 
The housing number I quoted should be an M91 not M1.
This housing will work for both types. Your existing valve body will be re-used and bolts to the new housing. Please check with your supplier as to the make-up of this part number, as my book shows the housing supplied with the needle roller bearing and seal fitted to it, hence the M91 denote.
Replace the valve body gasket as well.
 
I contacted the Massey dealer here today and said it appears that this tractor has been changed over to the new kpart and the what I thought was a bushing is all that is left of the needle bearing. I never did find any parts of it in the tranny or gear box so not sure what happened to the rest of it. I got the right parts on order sould come in next week I will let you know if they work. Thanks for all the help I really appreciate it.
 
You must log in or register to reply here.

Similar threads

P
Massey 165 question about engine sump
Replies
5
Views
252
PEI Massey165
P
C
1969 Massey Ferguson 165 weak/pulsing 3 point
Replies
8
Views
183
Cstrayer
C
S
Massey 180 multipower input shaft leak
Replies
17
Views
2K
steve682
S
L
TE 20 DRIVE PROBLEM
Replies
1
Views
120
used red MN
U
F
641 sherman transmission
Replies
8
Views
836
michford
michford
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top