Yesterday's Tractor Co. Affordable Parts, Just in Time
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Classified Ads
Photo Ads

Community
Discussion Forums
Project Journals
Tractor Town
Your Stories
Show & Pull Guide
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

Related Sites
Tractor Shed
TractorLinks.com
Ford 8N/9N Club
Today's Tractors
Garden Tractors
Classic Trucks
Kountry Life
Enter your email address to receive our newsletter!

subscribe
unsubscribe
  
John Deere Tractors Discussion Forum
Show Parts for Model:

70 pony motor

Welcome Guest, Log in or Register
Author  [Modern View]
George Holbrook

09-25-2012 15:53:46
76.5.96.236



Report to Moderator

Pony motor runs good the pinion engages as it should but its like the clutch just went out?
It"s been working fine..No slipage or engaging problems.The pinion just isn"t turning at all.
Its like the pinion drive has been disconnected from the clutch.Is there a shear pin in this drive somewhere?Help
Thanks George




[Log in to Reply]   [No Email]
LarrySTN

09-26-2012 04:43:20
71.54.89.157



Report to Moderator
 Re: 70 pony motor in reply to George Holbrook, 09-25-2012 15:53:46  
IIRC, when my 70D did that, a spring had broken. I am certain I was able to make the repair without any major surgery on the tractor.



[Log in to Reply]  [No Email]
wijim

09-25-2012 18:12:17
166.182.3.229



Report to Moderator
 Re: 70 pony motor in reply to George Holbrook, 09-25-2012 15:53:46  
Just had a thought, take the cover off the top of the pony trans and see if a pin didnt fall out of the linkage.



[Log in to Reply]  [No Email]
wijim

09-25-2012 18:09:35
166.182.3.209



Report to Moderator
 Re: 70 pony motor in reply to George Holbrook, 09-25-2012 15:53:46  
Nope no shear pin, must be clutch went out. It might start turning the pinion again if the clutch plates get jambed in there, but it will turn all the time and you wont get it to engage.



[Log in to Reply]  [No Email]
[Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:

TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ More Info ]

Home  |  Forums


Copyright © 1997-2014 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters