(800) 853-2651
SHOP NOW

Farmhand 810 or 815 owners

K

Kerwin

Member
For anyone who owns or has access to either a Farmhand 810 or 815 grinder mixer, can anyone send me or post a photo of the #40 roller chain that connects the intake auger to the gearbox input shaft? The 810 that I'm rebuilding did not have any method of applying tension to the chain, which allowed it to wear into a nearby pivot shaft.

I've attached a picture of the one I'm rebuilding without a chain tightener (it's the rear chain).
cvphoto21670.jpg


And here's a photo from an 815 that I parted out...this one has a chain tightener. But parts books for 810 and 815 show no chain tighteners at all.
cvphoto21672.jpg
 
I've got an 830, but have a 810 parts machine. will go look at it tomorrow. Don't know if I can post a picture, but will look and see if its like your part machine
 
Thanks. The parts catalog for the 810 and 815 show what is called a "guard" bolted on to the front of the intake auger bearing. Not sure if that somehow applied chain tension. That piece is missing from my 810.
 
How close is a F-81 to the models you have listed? We have a F-81 that we still use that i could get you pictures off of if it's close to what you need.
 
It depends on which version of an F-81. I think the 810 is an F-81D and the 815 started at F-81E, something like that. For example, my 810 lists F-81D as the model number on the SN plate, while the machine decal says 810. So, depending on the letter it could be similar or the same.
 
My 830 is at another place but checked it today. Hard to see with a shield in place, but it looks like it has a spring loaded tightener set up like the outside chain in your picture of the one you are working on.
 
It probably would be the same. Ours is a early model. B or C model. I know one letter is the model with the drop table and the other letter doesn't. Ours has the drop table.
 
You must log in or register to reply here.

Similar threads

L
JD M-20 Sickle Mower info/parts
Replies
6
Views
509
Landry
L
R
Maybe it was a bargain after all.
Replies
5
Views
872
J.Wondergem
J.Wondergem
M
Any IH 615 or 715 combine owners out there
Replies
3
Views
859
used red MN
U
G
new holland 276 tine bar
Replies
6
Views
1K
SVcummins
S
J
Farmhand F-81C feed grinder parts
Replies
1
Views
289
Jar7120
J
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top