(800) 853-2651
SHOP NOW

Vermeer 605A Baler - Torn Bottom Platform Belt

M

MOSteve

Member
My platform belt got torn and a new replacement costs much more than the baler is worth.

I'd like to replace the platform belt with a used belt from a tractor salvage yard (taken off the baler and stored inside once they acquired it).

The issue is that the platform belts the salvage yard has are off a Vermeer 605C. From pictures there doesn't seem to be much difference between the Vermeer 605 a, b or c models.

Does anyone know if the platform belt off a c model will fit on my a model?

Thanks
 
(quoted from post at 15:02:23 10/03/14) My platform belt got torn and a new replacement costs much more than the baler is worth.

I'd like to replace the platform belt with a used belt from a tractor salvage yard (taken off the baler and stored inside once they acquired it).

The issue is that the platform belts the salvage yard has are off a Vermeer 605C. From pictures there doesn't seem to be much difference between the Vermeer 605 a, b or c models.

Does anyone know if the platform belt off a c model will fit on my a model?

Thanks
Click to expand...
's don't have a platform belt, they have rollers on the bottom.
Don't know about the B's,...i never even seen one.
 
(quoted from post at 23:02:23 10/03/14) My platform belt got torn and a new replacement costs much more than the baler is worth.

I'd like to replace the platform belt with a used belt from a tractor salvage yard (taken off the baler and stored inside once they acquired it).

The issue is that the platform belts the salvage yard has are off a Vermeer 605C. From pictures there doesn't seem to be much difference between the Vermeer 605 a, b or c models.

Does anyone know if the platform belt off a c model will fit on my a model?

Thanks
Click to expand...

The 605C didn't use a platform belt but I'm pretty sure the B did.
 
When I had Gehl balers with table belts,I'd get reconditioned belts from Gehl. They had Dutchman splices in them. They'd cut about 6 inches off each end and put in another piece a foot long with two laces in them.
 
You must log in or register to reply here.

Similar threads

S
  • Question
Round baler rubber roller decorating DIY?
Replies
8
Views
282
Destroked 450
Destroked 450
J
Baler belt lacing
Replies
5
Views
486
MJMJ
M
D
Vermeer 504 F/G/H Twine Arm
Replies
1
Views
480
Hay RX
H
B
Vermeer 554xl Questions
Replies
4
Views
911
Doug Wi
D
jon f mn
Vermeer baler issues
Replies
8
Views
363
SVcummins
S
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top