(800) 853-2651
SHOP NOW

JD 535 Baler- Beyond Frustrated

Z

Zach Scherf

Member
Bought the baler last week and it sure eats hay great! The only
problem is the wrapping. I bale until the light turns solid, alarm
sounds, I push in the clutch and stop. The light doesn't go off
or anything, the net wrap just keeps going on, it never cuts it or
even tries to cut it. Any thing I can do? The only way to get it to
cut a bale is when it gets full, have a second person with me
and I pull the manual wrap. I wait a few seconds then pull it
again and it cuts it, then I have them shut off the pto and pull
the bale out. It has not been a fun weekend, any advice?
Deere has been closed and didn't give me the manual they
have for it despite me asking three times. Thoroughly
disappointed
 

Zach
It's been many yrs since I owned a JD rd baler with hyd operated netwrap. Will twine arms cycle correctly IE move from home to RH side and then back to LH side? Does net knife cycle and not cut net or not cycle at all? It's possible the spool shift valve by hyd pump is dirty and not shifting correctly. Have you checked hyd oil level in pump? What condition is pump drive belt?
 
Tx Jim the belt is in decent shape and turns the pump over good. I don't think it even tries to cycle the knife, it starts the wrap but doesn't move to shut it off, what tells it to stop wrapping and cut it? Also, the twine arms don't move right now, the only thing that moves during wrapping is the net gets feed into the chambe is it normal not to move the twine arms? I don't know how to email, you can call at 2195611353 if you want to. I asked John Deere about adjusting it they want a hundred bucks an hour including the driving time out here which is an hour each way
 

Zach
This is the valve I was talking about in our phone conversation. Be sure the spool moves up/down freely IE not sticking.
Jim
mvphoto7295.gif
 
You must log in or register to reply here.

Similar threads

M
JD 467 baler monitor question
Replies
3
Views
257
Mshudgins
M
S
What Round baler to buy
Replies
13
Views
1K
DanielW
D
B
Round Baler Twine Wrap Technique
Replies
10
Views
960
Bill VA
B
F
another ? round baler
Replies
19
Views
627
Bruce from Can.
Bruce from Can.
B
Ih 430 baler, square baler in general question
Replies
8
Views
1K
Leroy
L
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top