Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
Classified Ads
Photo Ads
Tractor Parts

Discussion Forums
Project Journals
Tractor Town
Your Stories
Show & Pull Guide
Events Calendar
Hauling Schedule

Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs

Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

Related Sites
Tractor Shed
Ford 8N/9N Club
Today's Tractors
Garden Tractors
Classic Trucks
Kountry Life
Implement Alley Discussion Forum

Re: surface drive badger unloader

[Show Entire Topic]  

Welcome Guest, Log in or Register
Author  [Modern View]
Roger Tomfohrde

12-27-2012 05:20:34

Report to Moderator

This might get a little long; If this is the one like we had there is several steps. First unbolt at the drive wheels from the support that keeps the wheels out. Remove the bolt from the plate on the end that keeps it from hitting the outside wall. Slide the wheels/weights off. Fold the two pieces of the drive assembly in towards the unloader body and tie them together, you may have to get the knuckle of the drive shaft turned so it will fold up along side. There should be weights hanging out away from the body of the unloader, take a picture of them so you can put them back the way they are now and move them closer to the unloader and hang all of the weights and wheels on the same shaft to balance the loader when it goes up. If I remember correctly the chute needs to come off also and get tied on top of the body of the unloader, I also beleive that the cable is remounted lower on a support for it by the blower. Tie a rope to the unloader so that when it is at the top it clears the fill chute, this rope should go through the inside chute the silage comes down. Once the unloader is up the fill chute might have to be extended out so it is in position. On ours the unloader would be above the fill chute when it was extended.Make sure everything is tied on securely before pulling the unloader so nothing falls off.We got the bolts so we only needed three wrenches, one 9/16 and two 3/4 inch, but they rust so your may be different. I sure liked it when we went to ring drives as it was easier to get ready to pull. Took about an hour and a half average to pull the badger(s). and 45 minutes for the ring drives. I may have missed some things in this and others should be along soon who are more current in pulling one of these. It has been awhile since I did one.

[Log in to Reply]   [No Email]
[Show Entire Topic]     [Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:

Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

Home  |  Forums

Copyright © 1997-2016 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters