Yesterday's Tractor Co. Trusted Parts Supplier since 1995
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 
Marketplace
Tractor Manuals
Tractor Parts
Classified Ads
Photo Ads

Community
Discussion Forums
Project Journals
Tractor Town
Your Stories
Show & Pull Guide
Events Calendar
Hauling Schedule

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Articles
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs
Glossary

Miscellaneous
Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

Related Sites
Tractor Shed
TractorLinks.com
Ford 8N/9N Club
Today's Tractors
Garden Tractors
Classic Trucks
Kountry Life
Enter your email address to receive our newsletter!

subscribe
unsubscribe
  
Implement Alley Discussion Forum

Re: Skid steer brush cutter?

[Show Entire Topic]  

Author  [Modern View]
Our Farmer

12-10-2012 08:55:46
75.243.134.50



Report to Moderator

Thanks, Phil.
The loader is rated 20-25 gph @ 3000psi, and a 1500 lb lift, so I'm not too concerned on that front. I found an "ambusher" for rent that's rated for an equivalent Bobcat ( low- flow, 40 hp) so I'm gonna invest a hundred bucks in product research before I start fabbin'.
My biggest worry is flats from running my new pnuematic tires over all those ponty little stumps!




[Reply]   [No Email]
Diydave

12-10-2012 16:16:46
96.244.157.254



Report to Moderator
 Re: Skid steer brush cutter? in reply to Our Farmer, 12-10-2012 08:55:46  
Take your hyd specs over to surpluscenter.com, and you will be able to shop for a hyd motor, that meets them. My ASV RC30 is 10 gpm, and 3000psi, the motor I got, used from them is still running good. They have a good technical service department, and can help you figure out what you will need, even if you don't end up buying from them. I used 1/4" plate, for my deck, and built it so I can't get the blades and stump jumper lower than 3-4" from the ground. Make sure all the mechanicals in your donor mower are good, I later had to replace the stump jumper and blade pins.

[Reply]  [No Email]
Our Farmer

12-10-2012 12:27:08
75.243.134.50



Report to Moderator
 Re: Skid steer brush cutter? in reply to Our Farmer, 12-10-2012 08:55:46  
Boy, was I optimistic!
Just checked the manual--15.5GPH @ 1000psi. Still enough, but not with the motor I have. Surplus center, here I come.



[Reply]  [No Email]
Phil Tibbetts

12-10-2012 15:48:19
208.93.14.38



Report to Moderator
 Re: Skid steer brush cutter? in reply to Our Farmer, 12-10-2012 12:27:08  
Think you mean GPM not GPH.



[Reply]  [No Email]
[Show Entire Topic]     [Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Add a Reply]

Hop to:
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ More Info ]

Home  |  Forums


Copyright © 1997-2014 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters