|
| |
| Implement Alley Discussion Forum |
Topic: JD Manure Spreader Model H Floor
[Return to Forum]
| Author |
[Modern View]
|
| JD Gimpl
07-27-2012 21:56:33
97.125.1.130
|
Hello Everyone
I finally got the rusted floor out of my new old spreader. It was rusted out so bad I could not get accurate measurements. Does anyone know the length and width.Also I was going to use 16 sheet metal, does that sound correct. Also any other tips or tricks about this spreader would be greatly appreciated. Thanks kindly, Gimpl
|
|
|
| Garrett Darbe
07-28-2012 06:35:51
205.237.134.5
|
|
Re: JD Manure Spreader Model H Floor in reply to JD Gimpl, 07-27-2012 21:56:33
|
|
| It measures 43x91.5. That is what the original manual shows
|
|
|
| Phil Tibbetts
07-28-2012 03:59:26
208.93.14.38
|
|
Re: JD Manure Spreader Model H Floor in reply to JD Gimpl, 07-27-2012 21:56:33
|
|
| It will cost more but if I were going to all that work I would use stainless steel 1/16 would be fine. If using steel I would go heavier. If you use steel I would wash it out good after using and let it dry good then paint it with a rust inhibitor or linseed oil. IMO
|
|
|
| Jim in Ma.
07-28-2012 03:42:28
72.70.109.209
|
|
Re: JD Manure Spreader Model H Floor in reply to JD Gimpl, 07-27-2012 21:56:33
|
|
| When my Brother did his, he fliped it upside down and blocked it to weld. I don't remember the size but I want to say - It is a little narrower in the front. He bent the ends down to 90 degrees to make it more ridgid.
|
|
|
[Options]
[Printer Friendly]
[Return to Forum]
[Add a Reply]
| Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a Company you can trust and have generous return policies! Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ More Info ] |
Home
| Forums
Copyright © 1997-2013 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V. Yesterday's Tractors - Antique Tractor Headquarters |
About this site - Yesterday's Tractors is your one-stop source for antique tractors. If you are interested in older tractors you've come to the right place! Join more than 275,000 other classic tractor enthusiasts from all over the globe. We have many resources for antique tractor enthusiasts available including photos, classified ads, more than 24 tractor discussion forums, a show guide, values, specs and much more. Bookmark this site and come back often. Thanks for stopping by! Feel free to use our feedback form to send us your comments, suggestions and ideas.
|
|
|
