Yesterday's Tractor Co. Shop Now
   Allis Chalmers Case Farmall IH Ford 8N,9N,2N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
Classified Ads
Photo Ads
Tractor Parts

Discussion Forums
Project Journals
Tractor Town
Your Stories
Show & Pull Guide
Events Calendar
Hauling Schedule

Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads
Community Album
Photo Ad Archives

Research & Info
Tractor Registry
Tip of the Day
Safety Cartoons
Tractor Values
Serial Numbers
Tune-Up Guide
Paint Codes
List Prices
Production Nbrs
Tune-Up Specs
Torque Values
3-Point Specs

Tractor Games
Just For Kids
Virtual Show
Museum Guide
Memorial Page
Feedback Form

Yesterday's Tractors Facebook Page

Related Sites
Tractor Shed
Ford 8N/9N Club
Today's Tractors
Garden Tractors
Classic Trucks
Kountry Life
Discussion Forum

Re: Simms Fuel Injector Pump on 1960 Fordson Super Major

[Show Entire Topic]  

Welcome Guest, Log in or Register
Author  [Modern View]

10-16-2011 13:46:05

Report to Moderator

Thanks a lot!

Took the cover off, and the governor rod was stuck, causing the first spring not to move. I cleaned it up a bit, sprayed it with some WD-40, and the tractor runs better than it has in a long time!

[Log in to Reply]   [No Email]

10-16-2011 13:51:01

Report to Moderator
 Re: Simms Fuel Injector Pump on 1960 Fordson Super Major in reply to 182RDC, 10-16-2011 13:46:05  
The only thing is that there was no oil in there, but moisture and rust. How do I keep it lubricated so it doesn't happen again?

[Log in to Reply]  [No Email]
Bob Bancroft

10-17-2011 18:17:31

Report to Moderator
 Re: Simms Fuel Injector Pump on 1960 Fordson Super Major in reply to 182RDC, 10-16-2011 13:51:01  
I imagine that's about the same pump on my Ford 655A backhoe. When I bought it, the injector pump crankcase was dry except for a little rust colored fuel. I filled it with oil, changed it when I changed the engine oil. It worked for a couple years. It ran fine, but eventually started dumping its oil rather quickly into the engine crankcase. The local pump shop advised me that the seal had gone, probably because the bearing was shot. I took it to them, and sure enough, the front bearing fell apart upon disassembly.

[Log in to Reply]  [No Email]
[Show Entire Topic]     [Options]  [Printer Friendly]  [Posting Help]  [Return to Forum]   [Log in to Reply]

Hop to:

Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

Home  |  Forums

Copyright © 1997-2018 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters