Ford Hydraulic System Slideshow.

Ford9000puller · Jan 31, 2018

Last one for now. Hopefully I can find some more to do now that I have it figured out.
Ford Hydraulic System

Bern · Jan 31, 2018

As always, thanks for doing this.

I found the external spin-on filter something new. I've never seen one before, has anyone else? I don't even see a spot in the casting to mount it - were these dealer installed?

RickB · Feb 1, 2018

Very nice slide show! That filter is also new to me.

Ford9000puller · Feb 1, 2018

Friend of mine on Facebook said his Gold 981 has one. Only one I?ve heard of

WayneIA · Feb 1, 2018

In the 60s we install lots of the filter kits.. Dealer installed . Had to drill four holes with a paper template furnished with the kit, furnished by Ford. I have one on each of my old 960 and 860. Wish we could still get the kit.

WayneIA · Feb 1, 2018

Probably I would be the only one noticing the tandem hitched mower and hay conditioner shot in this film. Had one for probably 5 years until trading them for a NH haybine .Don.t think I have seen one until this film since. These films sure are bringing back memories. Thanks a million "9000puller"

Bern · Feb 1, 2018

That would explain why there are no marks on the casting for the filter mount. Similar to the old 8000-9600 tractors with their add on external filter.

Royse · Feb 1, 2018

Thanks again Puller!

Wayne, we pulled a tandem hitched sickle bar mower and
conditioner when I was young. They were green and yellow though.
Still have the tractor and mower. Conditioner is long gone.

Another thing I noticed in this slideshow is that I've been putting
this decal in the wrong place. Silly little thing, but there it is.

Greg NE · Feb 1, 2018

Wayne, is there any chance of getting the measurements to install the filter kit on a tractor? the reason I ask is that I pulled all the parts for the filter out of a tractor in a salvage yard and messed up and didn't measure the holes so I can put it on one of my tractors. Young and dumb at the time and figured I could figure it out from the inside of the center section!! Thanks either way. Greg NE

Ford9000puller · Feb 1, 2018

Don?t feel alone. I?ve noticed the tandem setup too. Ive stared at it every time I see it it one of my brochures. One day I would like to find one.

WayneIA · Feb 2, 2018

Yes there is a chance. LOL. Some warm weather and me making an effort to get over to the building site to do some measuring. My email should be open.

WayneIA · Feb 2, 2018

My setup was slightly different. Ford built a attachment to put a adjustable drawbar on the mower(weld on brackets) and with the blocks in place on the conditioner caster wheels making it a totally pull type conditioner. Really was an awful nice setup. Used it a lot.

Greg NE · Feb 2, 2018

email sent!

Royse · Feb 2, 2018

"Some warm weather and me making an effort to get over to the
building site to do some measuring. My email should be open."

Why not post them on the forum for everyone to benefit from?
No pressure of course.

WayneIA · Feb 2, 2018

Hopefully will do!!!

Ford Hydraulic System Slideshow.

Ford9000puller

Member

Bern

Well-known Member

RickB

Well-known Member

Ford9000puller

Member

WayneIA

Well-known Member

WayneIA

Well-known Member

Bern

Well-known Member

Royse

Well-known Member

Greg NE

Member

Ford9000puller

Member

WayneIA

Well-known Member

WayneIA

Well-known Member

Greg NE

Member

Royse

Well-known Member

WayneIA

Well-known Member

Similar threads